VALVE CLEARANCE (for Sedan) > ADJUSTMENT |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE ENGINE UNDER COVER RH |
| 3. REMOVE NO. 2 CYLINDER HEAD COVER |
![]() |
Remove the 4 nuts and cylinder head cover No. 2.
| 4. REMOVE NO. 1 IGNITION COIL |
![]() |
Disconnect the 4 ignition coil connectors.
![]() |
Remove the 4 bolts and 4 ignition coils.
| 5. DISCONNECT VENTILATION HOSE |
![]() |
Disconnect the ventilation hose.
| 6. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY |
![]() |
Disconnect fuel vapor feed hose assembly.
| 7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Disconnect the fuel injector connectors.
![]() |
Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.
![]() |
Remove the bolt and remove the wire harness bracket.
![]() |
Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.
Remove the gasket from the cylinder head cover sub-assembly.
| 8. INSPECT VALVE CLEARANCE |
Set the No. 1 cylinder to TDC/compression.
![]() |
Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.
![]() |
Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.
![]() |
Check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.
Turn the crankshaft 1 complete revolution (360°) and align its timing notch with the timing mark "0" of the oil pump.
![]() |
Check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.
| 9. ADJUST VALVE CLEARANCE |
![]() |
Remove the fan and generator V belt .
Remove the engine mounting insulator sub-assembly RH .
Set the No. 1 cylinder to TDC/compression.
![]() |
Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.
![]() |
Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.
![]() |
Place paint marks on the chain in the places where the timing marks of the camshaft timing sprocket and the camshaft timing gear are located.
![]() |
Using an 8 mm hexagon wrench, remove the screw plug.
![]() |
Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.
![]() |
Using a wrench, rotate No. 2 camshaft clockwise to push in the plunger of the chain tensioner.
![]() |
Remove the screwdriver from the service hole, then align the hole in the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.
![]() |
Using a wrench, hold the hexagonal lobe of No. 2 camshaft and remove the flange bolt.
![]() |
Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
![]() |
Remove the flange bolt and remove the camshaft timing sprocket.
![]() |
Remove No. 2 camshaft.
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove No. 2 camshaft bearing cap.
![]() |
Hold the chain by hand and remove the camshaft and the camshaft timing gear assembly.
![]() |
Tie the chain with a piece of string as shown in the illustration.
Remove the 16 valve lifters.
![]() |
Using a micrometer, measure the thickness of the removed lifter.
Calculate the thickness of a new lifter so that the valve clearance comes to within the specified values.
| A | Thickness of new lifter |
| B | Thickness of used lifter |
| C | Measured valve clearance |
Select a new lifter with a thickness as close to the calculated values as possible.

| Shim No. | Thickness | Shim No. | Thickness | Shim No. | Thickness |
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700(0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) |

| Shim No. | Thickness | Shim No. | Thickness | Shim No. | Thickness |
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700 (0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) |
Install the selected valve lifter.
Apply a light coat of engine oil to the camshaft and camshaft journals.
![]() |
Install the chain onto the camshaft timing gear with the paint mark and the timing mark aligned as shown in the illustration.
![]() |
Examine the front marks and the numbers on No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts in several steps in the sequence shown in the illustration.
![]() |
Install No. 2 camshaft.
![]() |
Hold the chain, and align the timing mark on the camshaft timing sprocket with the paint mark of the chain.
Align the alignment pin hole in the camshaft timing sprocket with the alignment pin of the camshaft, and install the sprocket onto the camshaft.
![]() |
Provisionally install the flange bolt.
![]() |
Examine the front marks and the numbers of No. 1 camshaft bearing cap and No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts in several steps, in the sequence shown in the illustration.
![]() |
Using a wrench, hold the hexagonal lobe of No. 2 camshaft and install the flange bolt.
Remove the bar from the timing chain tensioner.
![]() |
Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.
![]() |
Check that all the pairs of timing marks are aligned.
Apply adhesive to the 2 or 3 threads of the screw plug.
![]() |
Using an 8 mm hexagon wrench, install the screw plug.
Install the engine mounting insulator sub-assembly RH .
Install the fan and generator V belt .
Adjust the fan and generator V belt .
Inspect the fan and generator V belt .
| 10. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Install a new gasket to the cylinder head cover sub-assembly.
![]() |
Apply seal packing to the cylinder head as shown in the illustration.
Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
![]() |
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.
![]() |
Install the wire harness bracket with the bolt.
![]() |
Connect the connector and wire harness clamp shown in the illustration and connect the engine wire harness.
![]() |
Connect the fuel injector connectors.
| 11. CONNECT FUEL VAPOR FEED HOSE ASSEMBLY |
![]() |
Connect fuel vapor feed hose assembly.
| 12. CONNECT VENTILATION HOSE |
![]() |
Connect the ventilation hose.
| 13. INSTALL NO. 1 IGNITION COIL |
![]() |
Install the 4 ignition coils with the 4 bolts.
![]() |
| *1 | Body |
| *2 | Cap |
![]() |
Connect the 4 ignition coil connectors.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. CHECK FOR ENGINE OIL LEAKAGE |
| 16. INSTALL NO. 2 CYLINDER HEAD COVER |
![]() |
Tighten the 2 A nuts, then the 2 B nuts.
| 17. INSTALL ENGINE UNDER COVER RH |