CAMSHAFT (for Sedan) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. REMOVE ENGINE UNDER COVER RH |
| 3. REMOVE NO. 2 CYLINDER HEAD COVER |
![]() |
Remove the 4 nuts and cylinder head cover No. 2.
| 4. REMOVE NO. 1 IGNITION COIL |
![]() |
Disconnect the 4 ignition coil connectors.
![]() |
Remove the 4 bolts and 4 ignition coils.
| 5. DISCONNECT VENTILATION HOSE |
![]() |
Disconnect the ventilation hose.
| 6. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY |
![]() |
Disconnect fuel vapor feed hose assembly.
| 7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Disconnect the fuel injector connectors.
![]() |
Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.
![]() |
Remove the bolt and remove the wire harness bracket.
![]() |
Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.
Remove the gasket from the cylinder head cover sub-assembly.
| 8. REMOVE FAN AND GENERATOR V BELT |
![]() |
Loosen bolts A and B.
Release the fan and generator V belt tension and remove the fan and generator V belt.
| 9. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
![]() |
Place a wooden block on a jack underneath the oil pan sub-assembly.
| *1 | Wooden Block |
![]() |
Remove the 5 bolts, the nut and the engine mounting insulator sub-assembly RH from the transverse engine engine mounting bracket and the vehicle.
| 10. REMOVE NO. 2 CAMSHAFT |
![]() |
Set the No. 1 cylinder to TDC / compression.
![]() |
Turn the crankshaft damper, and align its timing notch with the timing mark "0" of the oil pump.
![]() |
Check that the timing marks on both the camshaft timing sprocket and the camshaft timing gear are facing upward, as shown in the illustration.
![]() |
Place paint marks on the chain in the places where the timing marks of the camshaft timing sprocket and the camshaft timing gear are located.
![]() |
Using an 8 mm hexagon wrench, remove the screw plug.
![]() |
Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.
![]() |
Using a wrench, rotate No. 2 camshaft clockwise to push in the plunger of the chain tensioner.
![]() |
Remove the screwdriver from the service hole, then align the hole in the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.
![]() |
Using a wrench, hold the hexagonal lobe of No. 2 camshaft and remove the flange bolt.
![]() |
Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove camshaft bearing caps No. 1 and No. 2.
![]() |
Remove the flange bolt and remove the camshaft timing sprocket.
![]() |
Remove No. 2 camshaft.
| 11. REMOVE CAMSHAFT |
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove No. 2 camshaft bearing cap.
![]() |
Hold the chain by hand, and remove the camshaft and the camshaft timing gear assembly.
![]() |
Tie the chain with a piece of string as shown in the illustration.
| 12. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
Clamp the camshaft in a vise and confirm that it is locked.
![]() |
Cover the 4 oil paths of the cam journal with tape as shown in the illustration.
Puncture the tape covering the advance oil path and the retard oil path on the opposite side from the advance oil path.
![]() |
Apply air at about 150 kPa (1.5 kgf/cm2) pressure into the 2 broken paths (the advance side path and the retard side path).
![]() |
Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.
When the camshaft timing gear reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.
![]() |
Remove the flange bolt and remove the camshaft timing gear assembly.