CAMSHAFT (for Hatchback) > REMOVAL |
| 1. REMOVE ENGINE UNDER COVER RH |
| 2. REMOVE NO. 2 CYLINDER HEAD COVER |
![]() |
Remove the 4 nuts and No. 2 cylinder head cover.
| 3. DISCONNECT VENTILATION HOSE |
![]() |
Disconnect the ventilation hose.
| 4. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY |
![]() |
Disconnect the fuel vapor feed hose assembly.
| 5. REMOVE NO. 1 IGNITION COIL |
![]() |
Disconnect the 4 No. 1 ignition coil connectors.
![]() |
Remove the 4 bolts and the 4 No. 1 ignition coils.
| 6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Disconnect the fuel injector connectors.
![]() |
Disconnect the connector and 3 wire harness clamps shown in the illustration and disconnect the engine wire harness.
![]() |
Remove the bolt and remove the wire harness bracket.
![]() |
Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.
Remove the gasket from the cylinder head cover sub-assembly.
| 7. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
![]() |
Place a wooden block on a jack underneath the oil pan sub-assembly.
| *1 | Wooden Block |
![]() |
Remove the 4 bolts, the 2 nuts and the engine mounting insulator sub-assembly RH from the transverse engine engine mounting bracket and the vehicle.
| 8. REMOVE NO. 2 CAMSHAFT |
![]() |
| *a | Alignment Mark |
Set the No. 1 cylinder to TDC/compression.
![]() |
Turn the crankshaft damper, and align the timing notch with the timing mark "0" of the oil pump.
| *a | Timing Notch |
![]() |
Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.
| *a | Timing Mark |
![]() |
Place paint marks on the chain where it touches the timing marks on the camshaft timing sprocket and the camshaft timing gear.
| *a | Paint Mark |
| *b | Timing Mark |
![]() |
Using an 8 mm (0.31 in.) hexagon wrench, remove the screw plug.
![]() |
Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.
| *1 | Stopper Plate |
![]() |
Using a wrench, rotate the No. 2 camshaft clockwise to push in the plunger of the chain tensioner.
| *1 | Plunger |
![]() |
Remove the screwdriver from the service hole, then align the hole the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.
![]() |
Using a wrench, hold the hexagonal lobe of the No. 2 camshaft and remove the flange bolt.
![]() |
Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove the No. 1 and No. 2 camshaft bearing caps.
![]() |
Remove the flange bolt and the camshaft timing sprocket.
![]() |
Remove the No. 2 camshaft.
| 9. REMOVE CAMSHAFT |
![]() |
Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove the No. 2 camshaft bearing cap.
![]() |
Hold the chain by hand, and remove the camshaft and the camshaft timing gear assembly.
![]() |
Tie the chain with a piece of string as shown in the illustration.
| 10. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
Clamp the camshaft in a vise and confirm that it is locked.
![]() |
Cover the 4 oil paths of the cam journal with tape as shown in the illustration.
| *1 | Rubber Piece |
| *2 | Vinyl Tape |
| *a | Advance Side Path |
| *b | Retard Side Path |
| *c | Open |
| *d | Close |
Puncture the tape covering the advance oil path and the retard oil path on the opposite side from the advance oil path.
![]() |
Apply air at about 150 kPa (1.5 kgf/cm2) pressure into the 2 broken paths (the advance side path and the retard side path).
| *a | Advance Side Path |
| *b | Retard Side Path |
![]() |
Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.
| *a | Advance Side Path |
| *b | Retard Side Path |
| *c | Hold Pressure |
| *d | Decompress |
When the camshaft timing gear reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.
![]() |
Remove the flange bolt and the camshaft timing gear assembly.