Home › Engine / Hybrid System › 1NZ-FE LUBRICATION › OIL PUMP (for Sedan)

OIL PUMP (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL OIL PUMP ASSEMBLY
  1. Install 2 new O-rings to the cylinder block sub-assembly and the oil pan sub-assembly.



  1. Apply seal packing to the oil pump assembly, cylinder head sub-assembly and the cylinder block sub-assembly as shown in the illustration.


    A294784E01


    Text in Illustration 
    *a
    Apply Seal Packing to the Inner Corners
    *b
    Seal Width (Other Part)
    *c
    Seal Width (Water Pump Part)
    *d
    Seal Packing Application Width 10 mm or more
    *e
    Apply enough seal packing so that it will protrude beyond the timing chain cover installation surface
    -
    -

    Seal packing:
    Water pump part: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.
    Other part: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying seal packing.
    3. Do not expose the seal to engine oil for at least 2 hours after the installation.



    A116558
  1. Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.



  1. Temporarily install the oil pump assembly with the 16 bolts and the nut.


    A280785E01

    NOTICE:
    Do not apply oil to the bolt A.

    HINT:
    Each bolt length is as follows.
    A: 30 mm (1.181 in.)
    B: 35 mm (1.378 in.)
    C: 20 mm (0.787 in.)
    E: 14 to 20 mm (0.551 to 0.787 in.), Double ended bolt

  1. Tighten the 16 bolts and nut in the sequence shown in the illustration.

    Torque:
    Bolt A:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }
    Bolt B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Bolt C:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Nut D:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Bolt E:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Be careful not to disturb the seal packing.
    2. After installing the oil pump assembly, install the transverse engine engine mounting bracket within 10 minutes.



2. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A116553
  1. Install the transverse engine engine mounting bracket to the oil pump assembly with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



3. INSTALL ENGINE WATER PUMP ASSEMBLY
  1. Install the engine water pump assembly through a new gasket with the 3 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



4. INSTALL WATER PUMP PULLEY
  1. Provisionally install the water pump pulley with the 3 bolts.



    A116191E01
  1. Using SST, hold the engine water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



5. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


A116179
  1. Apply a light coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    NOTICE:
    Do not twist the O-ring.



    A116178
  1. Install the camshaft timing oil control valve assembly with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    A116177
  1. Connect the camshaft timing oil control valve assembly connector.



6. INSTALL CRANKSHAFT POSITION SENSOR


A091817
  1. Apply a light coat of engine oil to the O-ring on the crankshaft position sensor.

  1. Install the crankshaft position sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    Do not twist the O-ring.

  1. Connect the crankshaft position sensor connector.



7. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
  1. Align the pin hole of the crankshaft damper sub-assembly with the pin of the crankshaft and install the crankshaft damper sub-assembly.

  1. Provisionally install the bolt.



    A280794E01
  1. Using SST, tighten the bolt while holding the crankshaft damper sub-assembly.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09213-58014   (90201-08131, 91111-50845)
    09330-00021   (09330-00030)

    Torque:
    128 N*m{ 1305 kgf*cm , 95 ft.*lbf }

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



8. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
  1. Install the engine mounting insulator sub-assembly RH to the transverse engine engine mounting bracket and vehicle with the 5 bolts and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Install a new gasket to the cylinder head cover sub-assembly.



    A115503E01
  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes of applying the seal packing.
    3. Do not start the engine for at least 2 hours after the installation.

  1. Install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.



    A035756E01
  1. Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7.0 ft.*lbf }



    A115491
  1. Install the wire harness bracket with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 9.6 ft.*lbf }



    A115490
  1. Connect the connector and wire harness clamp shown in the illustration and connect the engine wire harness.



    A115489
  1. Connect the fuel injector connectors.



10. INSTALL FUEL VAPOR FEED HOSE ASSEMBLY


A115488
  1. Connect fuel vapor feed hose assembly.



11. INSTALL VENTILATION HOSE


A115487
  1. Connect the ventilation hose.



12. INSTALL NO. 1 IGNITION COIL


    A115485
  1. Install the 4 ignition coils with the 4 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


    NOTICE:
    A268161E01
    If the body or cap of the ignition coil is dropped or subjected to a strong impact, replace the ignition coil with a new one.

    Text in Illustration 
    *1
    Body
    *2
    Cap



    A115484
  1. Connect the 4 ignition coil connectors.



13. INSTALL GENERATOR ASSEMBLY


A115420E01
  1. Provisionally install the generator with fixing bolt B.



    A115419E01
  1. Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }



    A115418
  1. Install the connector and the wire harness clamp.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }

  1. Install the terminal cap.



14. INSTALL FAN AND GENERATOR V BELT
  1. Provisionally install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Make sure that there is no foreign matter or liquid, such as oil, on the belt and pulleys.
    2. Make sure that the V belt is securely fitted into the rib grooves of the pulley.



15. ADJUST FAN AND GENERATOR V BELT


    A116198E02
  1. Insert an adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar toward the vehicle front to adjust the generator V belt tension .
    Text in Illustration 
    *a
    OK
    *b
    NG

    NOTICE:
    Do not insert the adjusting bar between the camshaft timing oil control valve assembly and generator assembly. It could damage the camshaft timing oil control valve assembly.



    A116197E01
  1. First tighten bolt A, then tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
    54 N*m{ 551 kgf*cm , 40 ft.*lbf } for bolt B



16. INSPECT FAN AND GENERATOR V BELT


B000543
  1. Check the belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the V-ribbed belt.

    HINT:
    1. The fan and generator V belt is cracked.
    2. The fan and generator V belt is worn out to the extent that the cords are exposed.
    3. The fan and generator V belt has chunks missing from the ribs.



    B075171E12
  1. Check that the belt fits properly in the ribbed grooves.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    HINT:
    Check with your hand, to confirm that the belt has not slipped out of the grooves on the bottom to the pulley. If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly.



    A116200E04
  1. Inspect the V belt deflection and tension.
    Text in Illustration 
    *A
    w/o Air Conditioner
    *B
    w/ Air Conditioner

    Deflection:
    Item
    Specified Condition
    New belt
    8.0 to 9.0 mm (0.31 to 0.35 in)
    Used belt
    12.5 to 13.5 mm (0.49 to 0.53 in)

    Tension:
    Item
    Specified Condition
    New belt
    700 to 800 N (71 to 82 kg, 157 to 180 lb)
    Used belt
    300 to 400 N (31 to 41 kg, 67 to 90 lb)

    If the V belt deflection is not as specified, adjust it.

    HINT:
    1. When inspecting the V belt deflection, apply 98 N (10 kgf) tensile force to it.
    2. Perform the V belt inspection and adjustment while the engine is cold.
    3. V-ribbed belt tension and deflection should be checked immediately after installation of a new belt, and after cranking the engine when inspecting a used belt.
    4. Check the V belt deflection at the point between the specified pulleys where the deflection is greatest.
    5. When installing a new belt, set its tension to the intermediate value of the specification.
    6. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    7. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
    8. V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
    9. When using a belt tension gauge, confirm its accuracy by using a master gauge first.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



18. ADD ENGINE OIL
  1. Add fresh engine oil.

    Standard Oil Grade:

    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy- conserving", SM "energy- conserving", SN "resource-conserving", or ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    2. 20W-50


    Standard Oil Capacity:

    Item
    Capacity
    Drain and refill with oil filter change
    3.7 liters (3.9 US qts, 3.3 Imp. qts)
    Drain and refill without oil filter change
    3.4 liters (3.6 US qts, 3.0 Imp. qts)
    Dry fill
    4.1 liters (4.3 US qts, 3.6 Imp. qts)

  1. Install the oil filler cap sub-assembly.



19. ADD COOLANT
  1. Tighten the radiator drain cock plug by hand.



    A206788E06
  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
    Text in Illustration 
    *a
    Filler Tube End
    *b
    Coolant Level
    *c
    20 mm (0.787 in.)

    Capacity:
    Transaxle Type
    Coolant Capacity
    Automatic Transaxle
    4.7 liters (5.0 US qts, 4.4 Imp. qts)
    Manual Transaxle
    4.8 liters (5.1 US qts, 4.5 Imp. qts)

    NOTICE:
    Do not substitute water for coolant.

    HINT:
    TOYOTA vehicle are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the reserve tank cap.



    A246002E04
  1. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
    Text in Illustration 
    *a
    Full Line
    *b
    Low Line

  1. Install the water filler cap sub-assembly securely.

  1. Install the reserve tank cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

      NOTICE:
      1. Make sure that the radiator reserve tank assembly still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough coolant, perform the following stop the engine, and wait until the coolant has cooled down, and add coolant until the radiator reserve tank assembly is filled to the full line.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the coolant starts to flow inside the hose.

  1. Stop the engine and wait until the coolant cools down.

  1. Recheck the coolant level inside the radiator reserve tank assembly. If it is below the full level, add coolant.



20. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low and full marks on the engine oil level dipstick.
    If the engine oil level is low, check for oil leakage and add engine oil up to the full level mark.

    NOTICE:
    Do not add engine oil to above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



21. INSPECT FOR OIL LEAK


22. INSPECT FOR COOLANT LEAK

CAUTION:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leaks. If there are no signs or traces of external engine coolant leaks, check the heater core, cylinder block and head.



23. INSTALL NO. 2 CYLINDER HEAD COVER


A116235E01
  1. Tighten the 2 A nuts, then the 2 B nuts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



24. INSTALL ENGINE UNDER COVER RH
  1. Install the engine under cover RH to the vehicle with the 2 bolts and the 2 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



25. INSTALL ENGINE UNDER COVER LH
  1. Install the engine under cover LH to the vehicle with the 3 bolts and the 4 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



26. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }