Home › Engine / Hybrid System › 1NZ-FE LUBRICATION › OIL PUMP (for Hatchback)

OIL PUMP (for Hatchback) > REMOVAL

for Preparation Click here


NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here)



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. REMOVE FRONT WHEEL RH


3. REMOVE ENGINE UNDER COVER LH
  1. Remove the 3 bolts, the 4 screws and the engine under cover LH from the vehicle.



4. REMOVE ENGINE UNDER COVER RH
  1. Remove the 2 bolts, the 2 screws and the engine under cover RH from the vehicle.



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap sub-assembly.

  1. Remove the oil pan drain plug and the gasket from the No. 2 oil pan sub-assembly, and drain the engine oil into a container.

  1. Clean and install the oil pan drain plug with a new gasket to the No. 2 oil pan sub-assembly.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }



6. DRAIN COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot coolant and steam to blow out from the radiator assembly.



    A302981E02
  1. Loosen the radiator drain cock plug.
    Text in Illustration 
    *1
    Water Filler Cap Sub-assembly
    *2
    Radiator Drain Cock Plug

  1. Remove the water filler cap sub-assembly, then drain the coolant.



7. REMOVE NO. 2 CYLINDER HEAD COVER


    A116235
  1. Remove the 4 nuts and No. 2 cylinder head cover.



8. REMOVE GENERATOR ASSEMBLY



9. REMOVE NO. 1 IGNITION COIL


    A156073
  1. Disconnect the 4 No. 1 ignition coil connectors.



    A156074
  1. Remove the 4 bolts and the 4 No. 1 ignition coils.



10. DISCONNECT VENTILATION HOSE


A115487
  1. Disconnect the ventilation hose.



11. DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY


A115488
  1. Disconnect the fuel vapor feed hose assembly.



12. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A115489
  1. Disconnect the fuel injector connectors.



    A260540
  1. Disconnect the connector and 4 wire harness clamps shown in the illustration and disconnect the engine wire harness.



    A115491
  1. Remove the bolt and the wire harness bracket.



    A066472
  1. Remove the 9 bolts, 2 nuts and 2 seal washers and then remove the cylinder head cover sub-assembly.



13. REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


A245785E01
  1. Place a wooden block on a jack underneath the oil pan sub-assembly.
    Text in Illustration 
    *1
    Wooden Block

    NOTICE:
    To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments onto the No. 2 oil pan sub-assembly.



    A248250
  1. Remove the 4 bolts, the 2 nuts and the engine mounting insulator sub-assembly RH from the transverse engine engine mounting bracket and the vehicle.



14. REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY


A116203E05


  1. Set the No. 1 cylinder to TDC/compression.

    1. Turn the crankshaft damper sub-assembly, and align its timing notch with timing mark "0" of the oil pump.
      Text in Illustration 
      *a
      Timing Notch



    2. A116204E07
    3. Check that the timing marks on the camshaft timing sprocket and the camshaft timing gear are all facing upward as shown in the illustration.
      Text in Illustration 
      *a
      Timing Mark
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A280793E01
  1. Using SST, loosen the bolt while holding the crankshaft damper sub-assembly.
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    SST
    09213-58014   (90201-08131, 91111-50845)
    09330-00021   (09330-00030)

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.

  1. Remove the SST and the bolt.

  1. Remove the crankshaft damper sub-assembly from the crankshaft.



15. REMOVE CRANKSHAFT POSITION SENSOR


    A183419
  1. Disconnect the camshaft position sensor connector.



    A183420
  1. Remove the bolt and camshaft position sensor.



16. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A116177
  1. Disconnect the camshaft timing oil control valve assembly connector.



    A116178
  1. Remove the bolt and camshaft timing oil control valve assembly.

  1. Remove the O-ring from the camshaft timing oil control valve assembly.



17. REMOVE WATER PUMP PULLEY


A065937
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 3 bolts and the water pump pulley.



18. REMOVE ENGINE WATER PUMP ASSEMBLY


A065938
  1. Remove the 3 bolts, 2 nuts the water pump assembly and water pump gasket.



19. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A116553
  1. Remove the 4 bolts and the transverse engine engine mounting bracket.



20. REMOVE OIL PUMP ASSEMBLY


A280784
  1. Remove the 16 bolts and the nut from the oil pump assembly.



    A116555E01
  1. Using a screwdriver with its tip wrapped in protective tape, remove the oil pump assembly by prying between the cylinder head sub-assembly and cylinder block sub-assembly.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Do not damage the contact surfaces of the oil pump assembly and oil pan sub-assembly.



    A116556
  1. Remove the 2 O-rings from the cylinder block sub-assembly and the oil pan sub-assembly.