Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › ENGINE UNIT (for Sedan)

ENGINE UNIT (for Sedan) > REASSEMBLY

for Preparation Click here



1. INSTALL STUD BOLT


  1. Using "TORX" socket wrench E5, install the 4 stud bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A154885E01



2. INSTALL OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.



    A155464E04
  1. Apply a continuous bead of seal packing to the oil pan mating surface as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes of applying seal packing.
    3. Do not expose the seal to engine oil for at least 2 hours after the installation.

  1. Install 2 new O-rings onto the cylinder block.



    A037067E03
  1. Using several steps, install and tighten the 13 bolts uniformly in the sequence shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Each bolt length is as follows:
    Bolt A 49 mm (1.93 in.)
    Bolt B 88 mm (3.47 in.)
    Bolt C 144 mm (5.67 in.)



3. INSTALL OIL STRAINER SUB-ASSEMBLY


A084113
  1. Install a new gasket and the oil strainer with the 2 nuts and the bolt.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



4. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing material from the contact surface.



    A081876E06
  1. Apply a continuous bead of seal packing (Diameter 2.5 to 3.5 mm (0.0984 to 0.1378 in.)) to the oil pan mating surface as shown in the illustration.
    Text in Illustration 
    *a
    Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes of applying seal packing.
    3. Do not expose the seal to engine oil within 2 hours of installation.
    4. Do not start the engine for at least 2 hours after the installation.

  1. Install the No. 2 oil pan with the 9 bolts and the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install the drain plug with a new gasket.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }



5. INSTALL OIL FILTER UNION


A079679E01
  1. Using a 12 mm (0.47 in.) hexagon wrench, install the oil filter union.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



6. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Gently screw the oil filter into place, and tighten it until the gasket comes into contact with the seat.



    A038018E02
  1. Using SST, tighten it an additional 3/4 turn.

    SST
    09228-06501  

    HINT:
    When using a torque wrench, tighten it to the specified torque.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



7. INSTALL CYLINDER HEAD GASKET


A117469E02
  1. Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
    Text in Illustration 
    *a
    Lot No.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Check the mounting orientation of the cylinder head gasket.
    3. Place the cylinder head on the cylinder head gently in order not to damage the gasket.



8. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
The cylinder head bolts are tightened in 2 successive steps.

  1. Apply a light coat of engine oil to the threads of the cylinder head bolts.



    A035288
  1. Using several steps, install and tighten the 10 cylinder head bolts and plate washers uniformly with an 8 mm bi-hexagon wrench, in the sequence shown in the illustration.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

  1. Mark the front of the cylinder head bolt with paint.



    A116959E04
  1. Retighten the cylinder head bolts 90° and then an additional by 90° as shown in the illustration.
    Text in Illustration 
    *a
    Paint Mark

  1. Check that the paint mark is now at a 180° angle from the front.



    A073748E06
  1. Apply a continuous bead of seal packing (Diameter 4.5 to 5.5 mm (0.177 to 0.217 in.)) as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or Equivalent

    Text in Illustration 
    *1
    Cylinder Head
    *2
    Cylinder Head Gasket
    *3
    Cylinder Block
    *a
    Seal Packing
    *b
    Diameter: 4.5 to 5.5 mm

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts within 15 minutes of applying the seal packing.



9. INSTALL ENGINE REAR OIL SEAL
  1. Apply MP grease to a new oil seal lip.

    NOTICE:
    Keep the lip free of foreign matter.



    A166929E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the cylinder block and oil pan.

    SST
    09223-56010  

    NOTICE:
    1. Do not tap the oil seal at an angle.
    2. Wipe any extra grease off the crankshaft.



10. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

NOTICE:
Install the camshaft timing gear assembly onto the camshaft with the lock pin of the camshaft timing gear assembly released.



    A116230E04
  1. Put the camshaft timing gear assembly and camshaft together with the straight pin of the groove.
    Text in Illustration 
    *1
    Straight Pin
    *a
    Groove

  1. Turn the camshaft timing gear assembly clockwise while pushing it gently toward the camshaft. When the pin fits into the groove, push to ensure a good fit.

    NOTICE:
    Do not turn the camshaft timing gear in the retard direction (to the right).

  1. Check that there is no clearance between the gear flange and the camshaft.

  1. Tighten the flange bolt with the camshaft timing gear fixed.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    NOTICE:
    1. Do not lock the camshaft timing gear assembly when tightening the bolt.
    2. Release the lock pin of the camshaft timing gear assembly first, and tighten the bolt when the lock pin is locked in the most retarded position.
    3. Tightening the bolts with the lock pin locked could cause breakage of the lock pin.

  1. Check that the camshaft timing gear assembly can move in the retard direction (to the right) and is locked in the most retarded position.



11. INSTALL CAMSHAFT
  1. Apply a light coat of engine oil to the camshaft journals.

  1. Place the camshaft on the cylinder head with the timing mark on the camshaft timing gear facing upward.



    A037103E04
  1. Examine the front marks and numbers and tighten the bolts in the sequence shown in the illustration.

    Torque:
    13 N*m{ 129 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten each bolt uniformly while keeping the camshaft level.



12. INSTALL CAMSHAFT TIMING SPROCKET


A032167E01
  1. Clamp the camshaft in a vise.

  1. Align the knock pin hole the camshaft timing sprocket with the knock pin of the camshaft, and install the camshaft timing sprocket with the flange bolt.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    NOTICE:
    Do not damage the camshaft.



13. INSTALL NO. 2 CAMSHAFT
  1. Apply a light coat of engine oil to the camshaft journals.

  1. Place the camshaft on the cylinder head with the timing mark on the camshaft timing gear facing upward.



    A116223E08
  1. Examine the front marks and numbers on the No. 1 and No. 2 camshaft bearing caps and check that the order is as shown in the illustration. Then uniformly tighten the bolts, in several steps, in the sequence shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Bearing Cap
    *2
    No. 2 Bearing Cap

    Torque:
    No. 2 bearing cap:
    13 N*m{ 129 kgf*cm , 9 ft.*lbf }
    No. 1 bearing cap:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Tighten each bolt uniformly while keeping the camshaft level.



14. INSTALL CAMSHAFT POSITION SENSOR


A080958E01
  1. Apply engine oil to the O-ring.

    NOTICE:
    If the O-ring is damaged, replace the camshaft position sensor.

  1. Install the camshaft position sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



15. INSTALL CHAIN SUB-ASSEMBLY


A116571E07
Text in Illustration 
*a
TDC
*b
Timing Mark
  1. Make sure that all the timing marks are in the positions (TDC) shown in the illustration.

    HINT:
    The positions of the timing marks may differ the predetermined positions due to the force of the valve spring.



    A116573E04
  1. Set the timing mark of the crankshaft in a position between 40 and 140° ATDC, as illustrated.
    Text in Illustration 
    *a
    Timing Mark
    *b
    40° to 140° ATDC



    A116574E08
  1. Set the camshaft timing gear and the camshaft timing sprocket in the positions (20° ATDC) shown in the illustration.

  1. Set the crankshaft in the position (20° ATDC) shown in the illustration.
    Text in Illustration 
    *a
    20° ATDC
    *b
    Timing Mark



    A116576
  1. Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



    A116577E05
  1. Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.

    HINT:
    Align the timing marks with the mark plates while turning the hexagonal service portion of the camshaft using a wrench.
    Text in Illustration 
    *a
    Mark Plate
    *b
    Timing Mark



16. INSTALL CHAIN TENSIONER SLIPPER


A116569
  1. Install the chain tensioner slipper.



17. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY


A116568
  1. Install the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Remove the bar from the No. 1 chain tensioner assembly.



18. INSTALL OIL PUMP SEAL


A166953E01
  1. Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover.

    SST
    09950-60010   (09951-00250, 09951-00380, 09952-06010)
    09950-70010   (09951-07100)

    NOTICE:
    1. Do not tap the oil seal at an angle.
    2. Keep the lip free of foreign matter.

  1. Apply MP grease to the oil seal lip.



19. INSTALL OIL PUMP ASSEMBLY
  1. Install 2 new O-rings to the cylinder block sub-assembly and the oil pan sub-assembly.



  1. Apply seal packing to the oil pump assembly, cylinder head sub-assembly and the cylinder block sub-assembly as shown in the illustration.


    A294784E01


    Text in Illustration 
    *a
    Apply Seal Packing to the Inner Corners
    *b
    Seal Width (Other Part)
    *c
    Seal Width (Water Pump Part)
    *d
    Seal Packing Application Width 10 mm or more
    *e
    Apply enough seal packing so that it will protrude beyond the timing chain cover installation surface
    -
    -

    Seal packing:
    Water pump part: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.
    Other part: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying seal packing.
    3. Do not expose the seal to engine oil for at least 2 hours after the installation.



    A116558
  1. Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.



  1. Temporarily install the oil pump assembly with the 16 bolts and the nut.


    A280785E01

    NOTICE:
    Do not apply oil to the bolt A.

    HINT:
    Each bolt length is as follows.
    A: 30 mm (1.181 in.)
    B: 35 mm (1.378 in.)
    C: 20 mm (0.787 in.)
    E: 14 to 20 mm (0.551 to 0.787 in.), Double ended bolt

  1. Tighten the 16 bolts and nut in the sequence shown in the illustration.

    Torque:
    Bolt A:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }
    Bolt B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Bolt C:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }
    Nut D:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }
    Bolt E:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    NOTICE:
    1. Be careful not to disturb the seal packing.
    2. After installing the oil pump assembly, install the transverse engine engine mounting bracket within 10 minutes.



20. INSTALL ENGINE WATER PUMP ASSEMBLY
  1. Install the engine water pump assembly through a new gasket with the 3 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



21. INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET


A116553
  1. Install the transverse engine engine mounting bracket to the oil pump assembly with the 4 bolts.

    Torque:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }



22. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
  1. Align the pin hole in the crankshaft damper with the pin position and install the crankshaft damper sub-assembly.

  1. Provisionally install the bolt.



    A117461E01
  1. Using 2 SSTs, tighten the bolt while holding the crankshaft damper sub-assembly.

    SST
    09213-14010   (91651-60865)
    09330-00021  

    Torque:
    128 N*m{ 1305 kgf*cm , 95 ft.*lbf }

    NOTICE:
    Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump assembly.



23. INSTALL WATER PUMP PULLEY
  1. Provisionally install the water pump pulley with the 3 bolts.



    A116191E01
  1. Using SST, hold the engine water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



24. INSPECT VALVE CLEARANCE

HINT:
Inspect the valve clearance when the engine is cold.



  1. Set the No. 1 cylinder to TDC/compression.



      A116203E01
    1. Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.



    2. A116204E01
    3. Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.

      HINT:
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A116201
  1. Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (cold):
      for intake:
      0.15 to 0.25 mm (0.006 to 0.010 in.)
      for exhaust:
      0.25 to 0.35 mm (0.010 to 0.014 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.

  1. Turn the crankshaft 1 complete revolution (360°) and align its timing notch with the timing mark "0" of the oil pump.



    A116202
  1. Check the valves indicated in the illustration.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (cold):
      for intake:
      0.15 to 0.25 mm (0.006 to 0.010 in.)
      for exhaust:
      0.25 to0.35 mm (0.010 to 0.014 in.)

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.



25. ADJUST VALVE CLEARANCE


A116206E01

NOTICE:
When rotating the camshaft with the timing chain removed, rotate the crankshaft damper counterclockwise 40° from the TDC and align its timing notch with the matchmark of the timing chain cover to prevent the pistons from coming into contact with the valves.

  1. Remove the fan and generator V belt .

  1. Remove the engine mounting insulator sub-assembly RH .



  1. Set the No. 1 cylinder to TDC/compression.



      A116203E01
    1. Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.



    2. A116204E01
    3. Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.

      HINT:
      If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



    A116207E01
  1. Place paint marks on the chain in the places where the timing marks of the camshaft timing sprocket and the camshaft timing gear are located.



    G100163
  1. Using an 8 mm hexagon wrench, remove the screw plug.



    A116209E01
  1. Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.



    A116210E01
  1. Using a wrench, rotate No. 2 camshaft clockwise to push in the plunger of the chain tensioner.



    A116212
  1. Remove the screwdriver from the service hole, then align the hole in the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.

    HINT:
    1. Fix the stopper plate using the bar while rotating the camshaft right and left slightly.
    2. Hold the bar with tape so that the bar does not come off.



    A116213
  1. Using a wrench, hold the hexagonal lobe of No. 2 camshaft and remove the flange bolt.



    A116214E01
  1. Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.



    A116215
  1. Remove the flange bolt and remove the camshaft timing sprocket.



    A116216
  1. Remove No. 2 camshaft.



    A116217E01
  1. Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove No. 2 camshaft bearing cap.

    NOTICE:
    Loosen each bolt uniformly while keeping the camshaft level.



    A116218
  1. Hold the chain by hand and remove the camshaft and the camshaft timing gear assembly.



    A035227E01
  1. Tie the chain with a piece of string as shown in the illustration.

  1. Remove the 16 valve lifters.



    A001082
  1. Using a micrometer, measure the thickness of the removed lifter.

  1. Calculate the thickness of a new lifter so that the valve clearance comes to within the specified values.
    A
    Thickness of new lifter
    B
    Thickness of used lifter
    C
    Measured valve clearance

    Valve clearance:
    Intake A = B + (C - 0.20 mm (0.008 in.))
    Exhaust A = B + (C - 0.30 mm (0.012 in.))



  1. Select a new lifter with a thickness as close to the calculated values as possible.

    HINT:
    Lifters are available in 35 sizes in increments of 0.020mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).



    A117457

    Intake valve clearance (cold):
    0.15 to 0.25 mm (0.006 to 0.010 in.)

    EXAMPLE:
    A 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0158 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 46 lifter.


    New Shim Thickness:

    Shim No.
    Thickness
    Shim No.
    Thickness
    Shim No.
    Thickness
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700(0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)




    A117458

    Exhaust valve clearance (Cold):
    0.25 to 0.35 mm (0.010 to 0.014 in.)

    EXAMPLE:
    A 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.440 mm (0.0173 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 48 lifter.


    New Shim Thickness:

    Shim No.
    Thickness
    Shim No.
    Thickness
    Shim No.
    Thickness
    06
    5.060 (0.1992)
    30
    5.300 (0.2087)
    54
    5.540 (0.2181)
    08
    5.080 (0.2000)
    32
    5.320 (0.2094)
    56
    5.560 (0.2189)
    10
    5.100 (0.2008)
    34
    5.340 (0.2102)
    58
    5.580 (0.2197)
    12
    5.120 (0.2016)
    36
    5.360 (0.2110)
    60
    5.600 (0.2205)
    14
    5.140 (0.2024)
    38
    5.380 (0.2118)
    62
    5.620 (0.2213)
    16
    5.160 (0.2031)
    40
    5.400 (0.2126)
    64
    5.640 (0.2220)
    18
    5.180 (0.2039)
    42
    5.420 (0.2134)
    66
    5.660 (0.2228)
    20
    5.200 (0.2047)
    44
    5.440 (0.2142)
    68
    5.680 (0.2236)
    22
    5.220 (0.2055)
    46
    5.460 (0.2150)
    70
    5.700 (0.2244)
    24
    5.240 (0.2063)
    48
    5.480 (0.2157)
    72
    5.720 (0.2252)
    26
    5.260 (0.2071)
    50
    5.500 (0.2165)
    74
    5.740 (0.2260)
    28
    5.280 (0.2079)
    52
    5.520 (0.2173)


  1. Install the selected valve lifter.

  1. Apply a light coat of engine oil to the camshaft and camshaft journals.



    A116220E01
  1. Install the chain onto the camshaft timing gear with the paint mark and the timing mark aligned as shown in the illustration.



    A116222E01
  1. Examine the front marks and the numbers on No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts in several steps in the sequence shown in the illustration.

    Torque:
    13 N*m{ 129 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten each bolt uniformly while keeping the camshaft level.



    A116216
  1. Install No. 2 camshaft.



    A116224E01
  1. Hold the chain, and align the timing mark on the camshaft timing sprocket with the paint mark of the chain.

  1. Align the alignment pin hole in the camshaft timing sprocket with the alignment pin of the camshaft, and install the sprocket onto the camshaft.



    A116215
  1. Provisionally install the flange bolt.



    A116223E07
  1. Examine the front marks and the numbers of No. 1 camshaft bearing cap and No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts in several steps, in the sequence shown in the illustration.

    Torque:
    for No. 2 bearing cap:
    13 N*m{ 129 kgf*cm , 9 ft.*lbf }
    for No. 1 bearing cap:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }

    NOTICE:
    Tighten each bolt uniformly while keeping the camshaft level.



    A116225
  1. Using a wrench, hold the hexagonal lobe of No. 2 camshaft and install the flange bolt.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. Remove the bar from the timing chain tensioner.



    A116203E01
  1. Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.



    A116207E01
  1. Check that all the pairs of timing marks are aligned.

  1. Apply adhesive to the 2 or 3 threads of the screw plug.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent



    G100163
  1. Using an 8 mm hexagon wrench, install the screw plug.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

  1. Install the engine mounting insulator sub-assembly RH .

  1. Install the fan and generator V belt .

  1. Adjust the fan and generator V belt .

  1. Inspect the fan and generator V belt .



26. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


A064872E01
  1. Apply a light coat of engine oil to a new O-ring, and install it onto the camshaft timing oil control valve.

  1. Install the camshaft timing oil control valve with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    NOTICE:
    Do not twist the O-ring.



27. INSTALL FUEL INJECTOR ASSEMBLY


A115499E01
  1. Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.

  1. Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.



    A115500E01
  1. While turning the fuel injector left and right, install it onto the fuel delivery pipe.

    NOTICE:
    1. Do not twist the O-ring.
    2. After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.



28. INSTALL INJECTOR VIBRATION INSULATOR


A115497
  1. Install 4 new injector vibration insulators onto the cylinder head.



29. INSTALL NO. 1 DELIVERY PIPE SPACER


A115501
  1. Install the 2 No. 1 delivery pipe spacers onto the cylinder head.

    NOTICE:
    Install the delivery pipe No. 1 spacer in the correct direction.



30. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY


A115494
  1. Install the fuel delivery pipe sub-assembly with the 4 fuel injectors, then provisionally install the 3 bolts.

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
    2. Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe sub-assembly.



    A115494E01
  1. Tighten the 3 bolts to the specified torque.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf } for bolt A
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for bolt B



31. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


A260538
  1. Install a new gasket onto the cylinder head cover.

  1. Apply seal packing to the cylinder head, as shown in the illustration.
    Text in Illustration 
    V100155
    Seal Packing

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
    3. Do not start engine for at least 2 hours after the installation.

  1. Provisionally install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.



    A035756E01
  1. Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



32. INSTALL VENTILATION VALVE SUB-ASSEMBLY


A080963E01
  1. Install the ventilation valve onto the cylinder head cover.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



33. INSTALL OIL LEVEL DIPSTICK GUIDE
  1. Apply engine oil to a new O-ring.

  1. Install the oil level dipstick guide with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



34. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring on the crankshaft position sensor.

    NOTICE:
    If the O-ring is damaged, replace the crankshaft position sensor.

  1. Install the crankshaft position sensor with the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



35. INSTALL OIL FILLER CAP GASKET
  1. Install the oil filler cap gasket onto the oil filler cap.



36. INSTALL OIL FILLER CAP SUB-ASSEMBLY
  1. Install the oil filler cap onto the cylinder head cover.



37. INSTALL THERMOSTAT
  1. Install a new gasket onto the thermostat.



    A116188E01
  1. Install the thermostat with the jiggle valve facing upward.

    HINT:
    The jiggle valve may be set within 10° on either side, as shown in the illustration.



38. INSTALL WATER INLET


A080960E01
  1. Install the water inlet with radiator hose using the 2 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }



39. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket on to the engine coolant temperature sensor.



    A117464E01
  1. Using a 19mm socket wrench, install the engine coolant temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



40. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


A050082E26
Text in Illustration 
*1
Adhesive
  1. Apply adhesive to the end 2 or 3 threads of the oil pressure switch.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    Do not start the engine for at least 1 hour after the installation.



    A117463
  1. Using a 24 mm deep socket wrench, install the oil pressure switch.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



41. INSTALL KNOCK SENSOR


A090881E01
  1. Install the knock sensor with the nut as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



42. INSTALL SPARK PLUG


A080968E01
  1. Using a 16 mm spark plug wrench, install the 4 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }