Home › Engine / Hybrid System › 1NZ-FE COOLING › WATER PUMP (for Sedan)

WATER PUMP (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE WATER PUMP ASSEMBLY
  1. Install the engine water pump assembly through a new gasket with the 3 bolts and 2 nuts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. INSTALL WATER PUMP PULLEY
  1. Provisionally install the water pump pulley with the 3 bolts.



    A116191E01
  1. Using SST, hold the engine water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Tighten the 3 bolts to the specified torque.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }



3. INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
  1. Install the engine mounting insulator sub-assembly RH to the transverse engine engine mounting bracket and vehicle with the 5 bolts and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }



4. INSTALL GENERATOR ASSEMBLY


A115420E01
  1. Provisionally install the generator with fixing bolt B.



    A115419E01
  1. Provisionally install the fan belt adjusting slider with fan belt adjusting slider fixing bolts A and B, then move the generator toward the cylinder block and tighten bolt B.

    Torque:
    11 N*m{ 112 kgf*cm , 8.1 ft.*lbf }



    A115418
  1. Install the connector and the wire harness clamp.

  1. Install terminal B with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7.2 ft.*lbf }

  1. Install the terminal cap.



5. INSTALL FAN & GENERATOR V BELT
  1. Provisionally install the fan and generator V belt onto each pulley.

    NOTICE:
    1. Make sure that there is no foreign matter or liquid, such as oil, on the belt and pulleys.
    2. Make sure that the V belt is securely fitted into the rib grooves of the pulley.



6. ADJUST FAN & GENERATOR V BELT


    A116198E02
  1. Insert an adjusting bar between the engine mounting bracket and generator assembly. Pull the adjusting bar toward the vehicle front to adjust the generator V belt tension .
    Text in Illustration 
    *a
    OK
    *b
    NG

    NOTICE:
    Do not insert the adjusting bar between the camshaft timing oil control valve assembly and generator assembly. It could damage the camshaft timing oil control valve assembly.



    A116197E01
  1. First tighten bolt A, then tighten bolt B.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf } for bolt A
    54 N*m{ 551 kgf*cm , 40 ft.*lbf } for bolt B



7. INSPECT FAN & GENERATOR V BELT


B000543
  1. Check the belt for wear, cracks or other signs of damage.
    If any of the following defects is found, replace the V-ribbed belt.

    HINT:
    1. The fan and generator V belt is cracked.
    2. The fan and generator V belt is worn out to the extent that the cords are exposed.
    3. The fan and generator V belt has chunks missing from the ribs.



    B075171E12
  1. Check that the belt fits properly in the ribbed grooves.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    HINT:
    Check with your hand, to confirm that the belt has not slipped out of the grooves on the bottom to the pulley. If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt correctly.



    A116200E04
  1. Inspect the V belt deflection and tension.
    Text in Illustration 
    *A
    w/o Air Conditioner
    *B
    w/ Air Conditioner

    Deflection:
    Item
    Specified Condition
    New belt
    8.0 to 9.0 mm (0.31 to 0.35 in)
    Used belt
    12.5 to 13.5 mm (0.49 to 0.53 in)

    Tension:
    Item
    Specified Condition
    New belt
    700 to 800 N (71 to 82 kg, 157 to 180 lb)
    Used belt
    300 to 400 N (31 to 41 kg, 67 to 90 lb)

    If the V belt deflection is not as specified, adjust it.

    HINT:
    1. When inspecting the V belt deflection, apply 98 N (10 kgf) tensile force to it.
    2. Perform the V belt inspection and adjustment while the engine is cold.
    3. V-ribbed belt tension and deflection should be checked immediately after installation of a new belt, and after cranking the engine when inspecting a used belt.
    4. Check the V belt deflection at the point between the specified pulleys where the deflection is greatest.
    5. When installing a new belt, set its tension to the intermediate value of the specification.
    6. When inspecting a belt which has been used for over 5 minutes, apply the Used Belt specifications.
    7. When reinstalling a belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.
    8. V-ribbed belt tension and deflection should be checked after 2 revolutions of engine cranking.
    9. When using a belt tension gauge, confirm its accuracy by using a master gauge first.



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.



    A206788E06
  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
    Text in Illustration 
    *a
    Filler Tube End
    *b
    Coolant Level
    *c
    20 mm (0.787 in.)

    Capacity:
    Transaxle Type
    Coolant Capacity
    Automatic Transaxle
    4.7 liters (5.0 US qts, 4.4 Imp. qts)
    Manual Transaxle
    4.8 liters (5.1 US qts, 4.5 Imp. qts)

    NOTICE:
    Do not substitute water for coolant.

    HINT:
    TOYOTA vehicle are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the reserve tank cap.



    A246002E04
  1. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
    Text in Illustration 
    *a
    Full Line
    *b
    Low Line

  1. Install the water filler cap sub-assembly securely.

  1. Install the reserve tank cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens.
      While the thermostat is open, circulate the coolant for several minutes.

      NOTICE:
      1. Make sure that the radiator reserve tank assembly still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough coolant, perform the following stop the engine, and wait until the coolant has cooled down, and add coolant until the radiator reserve tank assembly is filled to the full line.

      HINT:
      The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the coolant starts to flow inside the hose.

  1. Stop the engine and wait until the coolant cools down.

  1. Recheck the coolant level inside the radiator reserve tank assembly. If it is below the full level, add coolant.



10. CHECK FOR ENGINE COOLANT LEAKAGE

CAUTION:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.



    A106594
  1. Fill the radiator assembly with engine coolant, and attach a radiator cap tester.

  1. Pump the tester to 118 kPa (1.2 kgf/cm2, 17.1 psi), and then check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator assembly and water pump assembly for leaks. If there are no signs or traces of external engine coolant leaks, check the heater core, cylinder block and head.



11. INSTALL ENGINE UNDER COVER RH