Home › Engine / Hybrid System › 1NZ-FE COOLING › RADIATOR (for Sedan)

RADIATOR (for Sedan) > REMOVAL


CAUTION:
Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.



1. DRAIN ENGINE COOLANT

NOTICE:
To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot coolant and steam to blow out from the radiator assembly.



    A302981E01
  1. Loosen the radiator drain cock plug.
    Text in Illustration 
    *1
    Water Filler Cap Sub-assembly
    *2
    Radiator Drain Cock Plug

  1. Remove the water filler cap sub-assembly, then drain coolant.



2. REMOVE FRONT BUMPER COVER


    B209115E02
  1. Apply protective tape, as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    B209117
  1. Remove the 7 screws and the 3 bolts.

  1. Remove the 2 screw grommets.

  1. Remove the 6 clips.



    B209118
  1. Disengage the 6 claws and remove the front bumper cover.

  1. Disconnect the connectors.



    B209120
  1. Remove the 2 clips and the screw grommet.



3. REMOVE AIR CLEANER ASSEMBLY


A117355
  1. Separate the intake air flow meter connector and the wire harness clamp.

  1. Separate the fuel vapor feed hose and fuel vapor feed hose No. 1 from the vacuum switching valve assembly.

  1. Separate the vacuum switching valve connector and the wire harness clamp.

  1. Separate the ventilation hose from the air cleaner hose.

  1. Release the air cleaner cap with air cleaner hose No. 1.

  1. Loosen the air cleaner hose clamp on the throttle body side and remove the air cleaner cap and the air cleaner hose.

  1. Remove the air cleaner element.



    A104895
  1. Separate the wire harness clamp from the air cleaner case.

  1. Remove the 2 bolts and remove the air cleaner case with air cleaner inlet No. 1.



4. REMOVE NO. 1 COOLER COVER (w/ No. 1 Cooler Cover)


A109229
  1. Remove the 2 clips and No. 1 cooler cover.



5. REMOVE HOOD LOCK ASSEMBLY (w/ Theft Deterrent System)


A108455
  1. Separate the hood lock control cable assembly from the 2 clamps.



    A117345
  1. Separate the engine hood courtesy switch connector.

  1. Remove the 3 bolts and remove the hood lock assembly.



6. REMOVE HOOD LOCK ASSEMBLY (w/o Theft Deterrent System)


A108455
  1. Separate the hood lock control cable assembly from the 2 clamps.



    A108456
  1. Remove the 3 bolts and remove the hood lock assembly.



7. REMOVE RADIATOR SUPPORT SUB-ASSEMBLY UPPER


A255858
  1. Separate the horn assembly connector.

  1. Remove the 4 bolts and remove the radiator support sub-assembly upper.



8. DISCONNECT RADIATOR RESERVOIR TANK HOSE


A117356
  1. Disconnect the radiator reservoir tank hose from the water filler.



9. REMOVE RADIATOR HOSE NO. 3


A117310E01
  1. Loosen the 2 clips and remove radiator hose No. 3.



10. DISCONNECT RADIATOR HOSE NO. 2


A104893
  1. Loosen the clip and disconnect radiator hose No. 2.



11. DISCONNECT OIL COOLER OUTLET HOSE (for Automatic Transaxle)


A117306
  1. Loosen the clip and disconnect the oil cooler outlet hose.



12. DISCONNECT OIL COOLER INLET HOSE (for Automatic Transaxle)


A117307
  1. Loosen the clip and disconnect the oil cooler inlet hose.



13. REMOVE RADIATOR ASSEMBLY (w/ Air Conditioning System)


A104896
  1. Separate the cooling fan motor connector and wire harness clamps.



    A104897
  1. Disengage the 2 claws and remove the radiator assembly from the vehicle.

    NOTICE:
    Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.



14. REMOVE RADIATOR ASSEMBLY (w/o Air Conditioning System)


A104896
  1. Separate the cooling fan motor connector and wire harness clamps.

  1. Remove the radiator assembly from the vehicle.



15. REMOVE RADIATOR HOSE NO. 2


A104898
  1. Loosen the clip and remove radiator hose No. 2.



16. REMOVE OIL COOLER OUTLET HOSE (for Automatic Transaxle)


A106602
  1. Loosen the clip and remove the cooler outlet hose.



17. REMOVE OIL COOLER INLET HOSE (for Automatic Transaxle)


A106603
  1. Loosen the clip and remove the cooler inlet hose.



18. REMOVE FAN SHROUD


A104899
  1. Disengage the 2 claws and remove the fan shroud.



19. REMOVE RADIATOR SUPPORT CUSHION


A104900
  1. Remove the 2 radiator support cushions from the radiator assembly.



20. REMOVE RADIATOR RESERVE TANK HOSE GROMMET


A106604
  1. Remove the 2 radiator reserve tank hose grommets from the radiator assembly.



21. REMOVE RADIATOR DRAIN COCK


A106605
  1. Remove the radiator drain cock from the radiator assembly.