Home › Engine / Hybrid System › 1NZ-FE LUBRICATION › OIL AND OIL FILTER (for Hatchback)

OIL AND OIL FILTER (for Hatchback) > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. Used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Take precautions when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves that cannot be penetrated by oil. Wash skin with soap and water, or use waterless hand cleaner, to completely remove any used engine oil. Do not use gasoline, thinner, or solvents.
  3. Dispose of used oil and used oil filters at designated disposal sites in order to preserve the environment.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap sub-assembly.

  1. Remove the oil pan drain plug and the gasket from the No. 2 oil pan sub-assembly, and drain the engine oil into a container.

  1. Clean and install the oil pan drain plug with a new gasket to the No. 2 oil pan sub-assembly.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }



2. REMOVE OIL FILTER SUB-ASSEMBLY


    A248714E02
  1. Using SST, remove the oil filter sub-assembly from the oil filter union.

    SST
    09228-06501  



3. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Clean the oil filter sub-assembly installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

  1. Lightly screw the oil filter sub-assembly into place by hand. Tighten oil filter sub-assembly until the gasket contacts the seat.



    A248715E01
  1. Using SST, tighten the oil filter sub-assembly an additional 3/4 turn.

    SST
    09228-06501  

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



4. ADD ENGINE OIL
  1. Add fresh engine oil.

    Standard Oil Grade (for USA, Canada):

    Oil Grade
    Oil Viscosity (SAE)
    ILSAC GF-5 multigrade engine oil
    5W-30


    Standard Oil Grade (for Mexico):

    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy- conserving", SM "energy- conserving", SN "resource-conserving", or ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    2. 20W-50


    Standard Oil Capacity:

    Item
    Capacity
    Drain and refill with oil filter change
    3.7 liters (3.9 US qts, 3.3 Imp. qts)
    Drain and refill without oil filter change
    3.4 liters (3.6 US qts, 3.0 Imp. qts)
    Dry fill
    4.1 liters (4.3 US qts, 3.6 Imp. qts)

  1. Install the oil filler cap sub-assembly.



5. INSPECT FOR OIL LEAK


6. INSPECT ENGINE OIL LEVEL
  1. Warm up and stop the engine, and then wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill with engine oil above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.