Home › Brake › BRAKE (FRONT) › FRONT BRAKE FLEXIBLE HOSE (for Sedan)

FRONT BRAKE FLEXIBLE HOSE (for Sedan) > INSTALLATION



1. INSTALL FRONT BRAKE FLEXIBLE HOSE


    C107599E01
  1. Install the flexible hose with a new union bolt and a new gasket.
    Text in Illustration 
    *a
    Lock Hole

    Torque:
    30 N*m{ 310 kgf*cm , 22 ft.*lbf }

    HINT:
    Install the flexible hose lock securely into the lock hole in the disc brake cylinder.

  1. w/ ABS:

    1. Install the flexible hose and the speed sensor with the bolt.

      Torque:
      29 N*m{ 300 kgf*cm , 22 ft.*lbf }

      NOTICE:
      Install the flexible hose and the speed sensor without twisting them.

  1. w/o ABS:

    1. Install the flexible hose with the bolt.

      Torque:
      29 N*m{ 300 kgf*cm , 22 ft.*lbf }

      NOTICE:
      Install the flexible hose without twisting it.

  1. Install a new clip.

  1. Using a union nut wrench, install the brake tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



2. FILL RESERVOIR WITH BRAKE FLUID


C241208
  1. Disengage the 3 clips and separate the hood to cowl top seal.

  1. Remove the cowl top ventilator louver.



    C241209
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



3. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C274940
  1. Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the master cylinder.



    C121826
  1. Slowly depress the brake pedal and hold it there (Step A).



    C121827
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat step A and B 3 or 4 times.



    C274940
  1. Using a 10 mm union nut wrench, connect the 2 brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat step C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



5. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



6. INSPECT FOR BRAKE FLUID LEAK


7. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }