Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL (for Sedan)

LOWER INSTRUMENT PANEL (for Sedan) > INSTALLATION



1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B132391E03
  1. Using a nipper, cut off both ends of the runner portion shown in the illustration (When installing a new one).
    Text in Illustration 
    *a
    Runner Portion
    *b
    Cut Off



  1. Install the lower instrument panel with the 6 <C> bolts, 2 <D> bolts, screw <F> and screw <G>.


    B349109E01

    NOTICE:
    Do not excessively tighten the <C> bolts, as this may damage the area not being tightened.

  1. Connect the clamps and connectors.

  1. Engage the 2 claws and connect the DLC3 connector.



2. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
  1. Engage the 3 claws to connect the control lever.



3. CONNECT ANTENNA CORD SUB-ASSEMBLY
  1. Connect the 5 antenna cord clamps.



4. INSTALL INSTRUMENT PANEL BOX
  1. Insert the stopper of the instrument panel box from the cutout of the lower instrument panel.



    B176559
  1. Engage the 2 hinges with the instrument panel open.

  1. Close the instrument panel box.



5. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY
  1. Install the 2 <A> screws.

  1. Engage the 7 claws and install the instrument panel lower finish panel.



6. INSTALL INSTRUMENT PAD LOWER RH
  1. Engage the claw and 3 clips and install the instrument pad lower.

  1. Install the <H> screw.



7. INSTALL INSTRUMENT PAD LOWER LH
  1. Engage the claw and 3 clips and install the instrument pad lower.

  1. Install the <H> screw.



8. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)


9. INSTALL COWL SIDE TRIM BOARD RH
  1. Engage the stud bolt and the claw and install the cowl side trim board.



10. INSTALL COWL SIDE TRIM BOARD LH

HINT:
Use the same procedure as for the RH side.



11. INSTALL FRONT DOOR SCUFF PLATE RH
  1. Engage the 11 claws and install the front door scuff plate.



12. INSTALL FRONT DOOR SCUFF PLATE LH

HINT:
Use the same procedure as for the RH side.



13. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY


I102570
  1. Engage the 2 claws and connect the air inlet damper control cable.



14. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY


I102569
  1. Engage the 2 claws and connect the defroster damper control cable.



15. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY


I102568
  1. Engage the 2 claws and connect the air mix control cable clamp.

  1. Connect the air mix damper control cable to the clamp.



16. INSTALL AIR CONDITIONING PANEL ASSEMBLY


I102567
  1. Connect the 3 connectors and the 4 clamps.



    I102566
  1. Engage the 4 clips and 2 claws and install the air conditioning panel.



17. INSTALL STEREO OPENING COVER
  1. Install the stereo opening cover with the 4 screws.



18. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
  1. Engage the 2 claws and 4 clips and install the instrument cluster finish panel center.



19. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


20. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING RH
  1. Install the spring.



21. INSTALL INSTRUMENT PANEL CUP HOLDER RH


    B349100
  1. Install the 2 hinges of the cup holder one at a time.

  1. Engage the spring with the instrument panel cup holder.

  1. Flex both sides of the cup holder and engage the 2 stoppers.

  1. Close the instrument panel cup holder.



22. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING LH
  1. Install the spring.



23. INSTALL INSTRUMENT PANEL CUP HOLDER LH


    B349101E01
  1. Install the 2 hinges of the cup holder one at a time.
    Text in Illustration 
    *1
    Instrument Panel Cup Holder Spring
    *a
    Stopper

    HINT:
    Make sure that the spring is set in the position shown in the illustration.

  1. Flex both sides of the cup holder and engage the 2 stoppers.

  1. Close the instrument panel cup holder.