Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL SYSTEM (for Sedan)

FUEL SYSTEM (for Sedan) > PRECAUTION



1.PRECAUTIONS
  1. Before working on the fuel system, disconnect the cable from the negative battery terminal.

  2. Do not work on the fuel system near any open flames. Never smoke during the work.

  3. Keep rubber and leather parts away from gasoline.


2.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Before removing any fuel system parts, take precautions to prevent gasoline spillage.
  2. As some pressure remains in the fuel line even after taking precautions to prevent gasoline spillage, use a piece of cloth to prevent gasoline splashes when disconnecting the fuel line.

  1. Remove the rear seat cushion .

  2. Remove the rear floor service hole cover.



  3. A115462
  4. Disconnect the fuel pump connector from the fuel pump assembly.

  5. Start the engine. After the engine stops naturally, turn the ignition switch OFF.

    HINT:
    DTC P0171 may be set.

  6. Crank the engine again and make sure that the engine does not start.

  7. Remove the fuel tank cap and discharge the pressure.

  8. Disconnect the cable from the negative battery terminal.

  9. Connect the fuel pump connector to the fuel pump assembly.


3.FUEL SYSTEM


  1. When disconnecting the high-pressure fuel line, a large amount of gasoline will splash. So take the following precautions.

    1. Discharge the fuel system pressure.

    2. Disconnect the fuel tube.

    3. Drain the fuel remaining inside the fuel pump tube.



    4. B000679E18
    5. Protect the contact surface by covering it with a plastic bag.
      Text in Illustration 
      *a
      Plastic Bag



  2. A125132E01
  3. Observe the following precautions when disconnecting the fuel tube connector (Quick Type A).
    Text in Illustration 
    *1
    No. 1 Fuel Pipe Clamp

    1. Remove the No. 1 fuel pipe clamp.

    2. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.



    3. A254817E01
    4. Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.
      Text in Illustration 
      *1
      Retainer
      *2
      Nylon Tube
      *3
      Pipe
      *4
      O-Ring
      *5
      Fuel Tube Connector
      V100135
      Pinch
      V100136
      Pull Out

      NOTICE:
      Do not use any tools.



    5. A193370
    6. If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.
      Text in Illustration 
      V100135
      Pull
      V100136
      Push

      NOTICE:
      Do not use any tools.

    7. Check the sealing surfaces of the disconnected parts, and clean them if necessary.



    8. A158902E03
    9. Protect the contact surface by covering it with a plastic bag.
      Text in Illustration 
      *a
      Plastic Bag

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



  4. A254813
  5. Observe the following precautions when connecting the fuel tube connectors (Quick Type A).
    Text in Illustration 
    V100135
    Push

    1. Check that there are no scratches or foreign objects on the connecting part.

    2. Line up the pipe and connector, and push them together until a "click" sound is heard.

      HINT:
      If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.



    3. A088340
    4. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
      Text in Illustration 
      V100136
      Pull

    5. Install the No. 1 fuel pipe clamp.

    6. Inspect for fuel leaks.



  6. A259877E01
  7. Observe the following procedure when disconnecting the fuel tube connectors (Quick Type B).
    Text in Illustration 
    *1
    Retainer
    V100135
    Pull
    V100136
    Pull Out

    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.

    2. Pull the tabs of the fuel tube connector retainer. Pull the retainer up to disconnect the fuel tube connector from the pipe.

      NOTICE:
      Do not use any tools.



    3. A259878
    4. If the connector and pipe are stuck, hold the fuel pipe by hand, and then push and pull on the connector. Pull the 2 pipes apart to separate the connector.
      Text in Illustration 
      V100135
      Pull
      V100136
      Push

      NOTICE:
      Do not use any tools.

    5. Check the sealing surfaces of the disconnected parts, and clean them if necessary.

      NOTICE:
      Do not use any tools.



    6. A259879E03
    7. Protect the contact surface by covering it with a plastic bag.
      Text in Illustration 
      *a
      Plastic Bag

      NOTICE:
      Do not damage the pipe or fuel tube connector, and prevent entry of foreign objects.



  8. A259880E01
  9. Observe the following procedure when connecting the fuel tube connector (Quick Type B).

    1. Check that there are no scratches or foreign objects on the connecting part.

    2. Line up the pipe and connector, and push them together until a "click" sound is heard. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
      Text in Illustration 
      *1
      Retainer
      V100135
      Push
      V100136
      Push

    3. After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.

    4. Inspect for fuel leaks.


4.INJECTOR


    A090674E07
  1. Install the injector into the delivery pipe and cylinder head, as shown in the illustration. Apply gasoline or spindle oil to the contact surfaces of the delivery pipe and injector before installing the injector.
    Text in Illustration 
    *1
    Fuel Delivery Pipe Sub-assembly
    *2
    Insulator
    *3
    O-ring



  2. A264991E03
  3. Observe the following precautions when removing and installing the fuel injector.
    Text in Illustration 
    *1
    O-ring
    *2
    Fuel Delivery Pipe Sub-assembly
    *a
    Correct
    *b
    Incorrect

    1. Do not reuse the O-ring and insulator.

    2. When placing a new O-ring onto the injector, do not damage the O-ring.

    3. Coat a new O-ring with gasoline or spindle oil before installing it. Do not use engine, gear or brake oil.


5.INSPECT FOR FUEL LEAK
  1. Check that there is no fuel leakage after performing maintenance anywhere on the fuel system .