METER / GAUGE SYSTEM (for Hatchback) > TERMINALS OF ECU |
| CHECK COMBINATION METER ASSEMBLY |

Disconnect the D100 combination meter assembly connector.
Measure the voltage and resistance of the wire harness side connector.
| Terminals No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D100-21 (ET) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| D100-39 (IG+) - Body ground | P - Body ground | Ignition switch signal | Ignition switch off → ON | Below 1 V → 11 to 14 V |
| D100-40 (B) - Body ground | L - Body ground | Battery | Always | 11 to 14 V |
| D101-1 (B) - Body ground | R - Body ground | Battery | Always | 11 to 14 V |
Reconnect the D100 combination meter assembly connector.
Measure the voltage, check for pulse and resistance of the wire harness side connector.
| Terminals No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| D100-5 (SI) - Body ground | L - Body ground | Speed signal (Input) | Driving at approximately 20 km/h (12 mph) | Pulse generation (See waveform 1) |
| D100-6 (+S) - Body ground | SB - Body ground | Speed signal (Output) | Driving at approximately 20 km/h (12 mph) | Pulse generation (See waveform 1) |
| D100-9 (S) - Body ground | Y - Body ground | Engine oil pressure signal | Engine oil pressure warning light ON → OFF | Below 1 V → 11 to 14 V |
| D100-10 (WLVL)*2 - Body ground | V - Body ground | Washer level warning signal | Ignition switch ON Washer level warning light ON → OFF | Below 1 V → 11 to 14 V |
| D100-11 (CHK) - Body ground | LG - Body ground | Check engine warning light signal | Check engine warning light ON → OFF | Below 1 V → 11 to 14 V |
| D100-12 (SW) - Body ground | GR - Body ground | Brake fluid level warning light signal | Ignition switch ON Brake fluid level warning light ON → OFF | Below 1 V → 11 to 14 V |
| D100-14 (-) - Body ground | BR - Body ground | High beam indicator signal (-) | Always | Below 1 V |
| D100-16 (L) - Body ground | G - Body ground | Fuel level signal | Ignition switch ON Fuel level is FULL → EMPTY | Below 1 V → 4.5 to 9.0 V |
| D100-17 (TC) - Body ground | SB - Body ground | TAIL cancel switch signal | TAIL cancel switch OFF → ON | 10 kΩ or higher → Below 1 Ω |
| D100-19 (+) - Body ground | GR - Body ground | High beam indicator signal (+) | High beam indicator ON → OFF | 11 to 14 V → Below 1 V |
| D100-20 (ILL+) - Body ground | R - Body ground | Taillight signal | Light control switch OFF → ON | Below 1 V → 11 to 14 V |
| D100-31 (CANL) - Body ground | W - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| D100-32 (CANH) - Body ground | G - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| D100-33 (SW3) - Body ground | W - Body ground | Light control rheostat switch ground | Always | Below 1 Ω |
| D100-34 (TX1-) - Body ground | B - Body ground | Outside temperature signal | Ignition switch ON outside temperature 25 °C | Approximately 1.3 V |
| D100-35 (TX1+) - Body ground | W - Body ground | Ground (Temperature ground) | Always | Below 1 Ω |
| D100-36 (SW2) - Body ground | Y - Body ground | Light control rheostat knob input | Light control rheostat knob fully turned downward | Below 1 Ω |
| Light control rheostat knob fully turned upward | 10 kΩ or higher | |||
| D100-37 (SW1) - Body ground | G - Body ground | Power source for light control rheostat | Ignition switch ON | 4.6 to 5.4 V |
| D101-3 (HAZ) - Body ground | L - Body ground | Hazard warning signal switch signal | Hazard warning signal switch off | 11 to 14 V |
| Hazard warning signal switch on | Below 1 Ω | |||
| D101-7 (LR) - Body ground | V - Body ground | Right turn signal | Ignition switch ON Right turn indicator light OFF → ON | Below 1 V → 11 to 14 V |
| D101-9 (ER) - Body ground | B - Body ground | Turn signal switch RH signal | Turn signal switch RH on | 11 to 14 V |
| Turn signal switch RH off | Below 1 Ω | |||
| D101-10 (EL) - Body ground | Y - Body ground | Turn signal switch LH signal | Turn signal switch LH on | 11 to 14 V |
| Turn signal switch LH off | Below 1 Ω | |||
| D101-12 (FOG)*1 - Body ground | BE - Body ground | Front fog signal | Ignition switch ON Front fog switch OFF → ON | Below 1 V → 11 to 14 V |
| D101-13 (LL) - Body ground | LG - Body ground | Left turn signal | Ignition switch ON Left turn indicator light OFF → ON | Below 1 V → 11 to 14 V |
![]() |
Waveform 1: Using an oscilloscope
| Terminal Connections | D100-6 (+S) and Body ground D100-5 (SI) and Body ground |
| Tool Setting | 5 V/DIV, 20 ms/DIV |
| Condition | Driving at approximately 20 km/h (12 mph) |
| CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (2 Connector Type) |

| *1 | Instrument Panel Junction Block Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) (Click here).
Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
| MB-29 (ACC) - Body ground | None - Body ground | Ignition power supply (ACC signal) | Ignition switch ACC | 11 to 14 V |
| MB-30 (BECU) - Body ground | None - Body ground | +B (power system signal system) power supply | Always | 11 to 14 V |
| MB-32 (IG) - Body ground | None - Body ground | Ignition power supply (IG signal) | Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU) (Click here).
Measure the voltage between each terminal of the wire harness side connectors and body ground.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| 3A-28 (PKB) - Body ground | R - Body ground | Parking brake signal | Parking brake warning light ON → OFF | Below 1 V → 11 to 14 V |
| D143-13 (CANL) - Body ground | W - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| D143-14 (CANH) - Body ground | R - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (1 Connector Type) |

| *1 | Instrument Panel Junction Block Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) (Click here).
Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
| MB-29 (ACC) - Body ground | None - Body ground | Ignition power supply (ACC signal) | Ignition switch ACC | 11 to 14 V |
| MB-30 (BECU) - Body ground | None - Body ground | +B (power system signal system) power supply | Always | 11 to 14 V |
| MB-32 (IG) - Body ground | None - Body ground | Ignition power supply (IG signal) | Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU) (Click here).
Measure the voltage between each terminal of the wire harness side connectors and body ground.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
| 3A-28 (PKB) - Body ground | R - Body ground | Parking brake signal | Parking brake warning light ON → OFF | Below 1 V → 11 to 14 V |
| D143-13 (CANL) - Body ground | W - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| D143-14 (CANH) - Body ground | R - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| COMBINATION METER INTERNAL CIRCUIT |




| Terminal No. | Wire Harness Side | |
| 5 | Brake actuator assembly (skid control ECU)*1 or Speedometer Sensor*2 | |
| 6 | Other ECU | |
| 9 | Engine oil pressure switch assembly | |
| 10*4 | Washer level warning switch | |
| 11 | ECM | |
| 12 | Brake fluid level warning switch | |
| 14 | Body ground | |
| 16 | Fuel sender gauge assembly | |
| 17 | Light control rheostat | |
| 19 | H-LP LH HI fuse | |
| 20 | Panel fuse | |
| 21 | Body ground | |
| 31 | CAN communication line | |
| 32 | CAN communication line | |
| 33 | Light control rheostat | |
| 34 | Ambient temperature sensor | |
| 35 | Ambient temperature sensor | |
| 36 | Light control rheostat | |
| 37 | Light control rheostat | |
| 39 | IG2 relay | |
| 40 | Battery | |
| D101 | 1 | Battery |
| 3 | Hazard warning signal switch assembly | |
| 7 | Turn signal light RH | |
| 9 | Headlight dimmer switch assembly (Turn signal switch) | |
| 10 | Headlight dimmer switch assembly (Turn signal switch) | |
| 12 | FR FOG relay*3 | |
| 13 | Turn signal light LH | |