Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Hatchback)

AIR CONDITIONING SYSTEM (for Hatchback) > PTC Heater Circuit


DESCRIPTION

The No. 2 integration relay is controlled in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.

WIRING DIAGRAM


E227905E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedures.

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Heater Active Level
    Heater level
    Min.: 0, Max.: 3
    -



    E220369E01
  1. Measure the voltage according to the value(s) in the table below while performing the Active Test.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    0 (DAG0) - Body ground
    Heater Active Level 1 to 3
    3.5 to 5 V
    1 (DAG1) - Body ground
    Heater Active Level 1 to 3
    3.5 to 5 V

    Text in Illustration 
    *a
    Upper View of No. 2 Integration Relay



NG
Go to step 4
OK


2.INSPECT QUICK HEATER ASSEMBLY
  1. Inspect the quick heater assembly (Click here).



NG
REPLACE QUICK HEATER ASSEMBLY (Click here)
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Disconnect the A69 quick heater assembly connector.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Heater Active Level
    Heater level
    Min.: 0, Max.: 3
    -



    E152214E10
  1. Measure the voltage according to the value(s) in the table below while performing the Active Test.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A69-1 (B) - Body ground
    Heater Active Level 0
    Below 1 V
    Heater Active Level 1
    Below 1 V
    Heater Active Level 2
    Below 1 V
    Heater Active Level 3
    11 to 14 V
    A69-2 (B) - Body ground
    Heater Active Level 0
    Below 1 V
    Heater Active Level 1
    11 to 14 V
    Heater Active Level 2
    11 to 14 V
    Heater Active Level 3
    11 to 14 V
    A69-3 (B) - Body ground
    Heater Active Level 0
    Below 1 V
    Heater Active Level 1
    Below 1 V
    Heater Active Level 2
    11 to 14 V
    Heater Active Level 3
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Quick Heater Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (QUICK HEATER ASSEMBLY - NO. 2 INTEGRATION RELAY)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - BATTERY AND IG1 NO. 1 RELAY)
E223246E01
  1. Remove the No. 2 integration relay from the No. 2 engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    2-1 (ALT) - Body ground
    Always
    11 to 14 V
    2C-2 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block
    *a
    Front view of wire harness connector
    (to No. 2 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - BODY GROUND)


    E219643E01
  1. Remove the No. 2 integration relay from the No. 2 engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2B-1 (GND1) - Body ground
    Always
    Below 1 Ω
    2C-16 (GND2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 Integration Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Remove the No. 2 integration relay from the No. 2 engine room relay block.

  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Heater Active Level
    Heater level
    Min.: 0, Max.: 3
    -



    E219644E01
  1. Measure the voltage according to the value(s) in the table below while performing the Active Test.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2C-12 (PTCA) - Body ground
    Heater Active Level 0
    Below 1 V
    Heater Active Level 1
    11 to 14 V
    Heater Active Level 2
    11 to 14 V
    Heater Active Level 3
    11 to 14 V
    2C-13 (PTCB) - Body ground
    Heater Active Level 0
    Below 1 V
    Heater Active Level 1
    Below 1 V
    Heater Active Level 2
    11 to 14 V
    Heater Active Level 3
    11 to 14 V
    2C-14 (PTCC) - Body ground
    Heater Active Level 0
    Below 1 V
    Heater Active Level 1
    Below 1 V
    Heater Active Level 2
    Below 1 V
    Heater Active Level 3
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 2 Integration Relay)



NG
Go to step 7
OK

REPLACE NO. 2 INTEGRATION RELAY 

7.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Remove the No. 2 integration relay from the No. 2 engine room relay block.

  1. Disconnect the D130 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2C-12 (PTCA) - D130-13 (PTC1)
    Always
    Below 1 Ω
    2C-13 (PTCB) - D130-19 (PTC2)
    Always
    Below 1 Ω
    2C-14 (PTCC) - D130-20 (PTC3)
    Always
    Below 1 Ω
    2C-12 (PTCA) - Body ground
    Always
    10 kΩ or higher
    2C-13 (PTCB) - Body ground
    Always
    10 kΩ or higher
    2C-14 (PTCC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)