FUEL SYSTEM (for Hatchback) > PRECAUTION |
| 1.PRECAUTIONS |
Before working on the fuel system, disconnect the cable from the negative battery terminal.
Do not work on the fuel system near any open flames. Never smoke when working on this system.
Keep rubber and leather parts away from gasoline.
| 2.DISCHARGE FUEL SYSTEM PRESSURE |
for 60/40 Split Seat Type LH Side:
Remove the rear seat assembly LH (Click here).
for 60/40 Split Seat Type RH Side:
Remove the rear seat assembly RH (Click here).
for Fold Down Seat Type:
Remove the rear seat assembly (Click here).
![]() |
Remove the rear floor service hole cover.
| *1 | Clip Remover |
| *2 | Protective Tape |
| *3 | Butyl Tape |
![]() |
Disconnect the connector from the fuel suction tube assembly with fuel pump and gauge assembly.
Start the engine.
After the engine stops naturally, turn the ignition switch off.
Crank the engine again and make sure that the engine does not start.
Remove the fuel tank cap and discharge the pressure from the fuel tank.
Disconnect the cable from the negative battery terminal.
Connect the connector of the fuel suction tube assembly with fuel pump and gauge assembly.
| 3.FUEL SYSTEM |
When disconnecting the high-pressure fuel line, a large amount of gasoline will splash out. Take the following precautions.
Discharge the fuel system pressure.
Remove the fuel tube clip.
Disconnect the fuel tube.
Drain the fuel remaining inside the fuel pump tube into a container.
![]() |
Protect the contact surface by covering it with a plastic bag.
| *1 | Plastic Bag |
Put a container under the connection part.
![]() |
Observe the following precautions when disconnecting the fuel tube connector (Quick Type A).
| *1 | No. 1 Fuel Pipe Clamp |
Remove the No. 1 fuel pipe clamp.
Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
![]() |
Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.
| *1 | Retainer |
| *2 | Nylon Tube |
| *3 | Pipe |
| *4 | O-Ring |
| *5 | Fuel Tube Connector |
![]() | Pinch |
![]() | Pull Out |
![]() |
If the connector and pipe are stuck, pinch the retainer with your hand, and then push and pull the connector to disconnect them.
![]() | Pull |
![]() | Push |
Check the sealing surfaces of the disconnected parts, and clean them if necessary.
![]() |
Protect the contact surface by covering it with a plastic bag.
| *1 | Plastic Bag |
![]() |
Observe the following precautions when connecting the fuel tube connectors (Quick Type A).
![]() | Push |
Check that there are no scratches or foreign objects on the connecting part.
Line up the pipe and connector and push them together until a "click" sound is heard.
![]() |
After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
![]() | Pull |
Install the No. 1 fuel pipe clamp.
Inspect for fuel leaks.
![]() |
Observe the following procedure when disconnecting the fuel tube connectors (Quick Type B).
| *1 | Retainer |
![]() | Pull |
![]() | Pull Out |
Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
Pull the tabs of the fuel tube connector retainer. Pull the retainer up to disconnect the fuel tube connector from the pipe.
![]() |
If the connector and pipe are stuck, hold the fuel pipe by hand and push and pull on the connector. Pull the two pipes apart to separate the connector.
![]() | Pull |
![]() | Push |
Check the sealing surfaces of the disconnected parts, and clean them if necessary.
Protect the contact surface by covering it with a plastic bag.
![]() |
Protect the contact surface by covering it with a plastic bag.
| *1 | Plastic Bag |
![]() |
Observe the following procedure when connecting the fuel tube connector (Quick Type B).
Check that there are no scratches or foreign objects on the connecting part.
Line up the pipe and connector and push them together until a "click" sound is heard. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
| *1 | Retainer |
![]() | Push |
![]() | Push |
After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
Inspect for fuel leaks.
| 4.INJECTOR |
![]() |
Observe the following precautions when removing and installing the fuel injector.
Do not reuse the O-ring and insulator.
When placing a new O-ring onto the injector, do not damage the O-ring.
Coat the new O-ring with gasoline or spindle oil before installing it. Do not use engine, gear or brake oil.
![]() |
Install the injector into the delivery pipe and cylinder head, as shown in the illustration. Apply gasoline or spindle oil to the contact surfaces of the delivery pipe and the injector before installing the injector.
| *1 | Delivery pipe |
| *2 | O-ring |
| *3 | Insulator |
| 5.INSPECT FOR FUEL LEAK |
Check that there is no fuel leakage after performing maintenance anywhere on the fuel system .