Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Hatchback Front Side)

SIDE AIRBAG SENSOR (for Hatchback Front Side) > INSTALLATION


CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).

HINT:
The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. INSTALL DOOR SIDE AIRBAG SENSOR
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Engage the guide and install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Connect the connector as shown in the illustration (when locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).


      C198070E06


      Text in Illustration 
      *1
      Outer Connector Locking Sleeve
      -
      -
      *a
      Slide
      -
      -

      HINT:
      When connected, the outer connector locking sleeve will slide. Be sure not to hold the outer connector locking sleeve while connecting, as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)


    B271597E01
  1. Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



    B271596
  1. Engage the 7 clips and install the front door trim board sub-assembly.



    B271595
  1. Install the 3 screws.



    B275407
  1. Engage the claw and close the cover.



3. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)


    B271597E01
  1. Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



    B284585
  1. Engage the 8 clips and install the front door trim board sub-assembly.



    B271595
  1. Install the 3 screws.



    B275407
  1. Engage the claw and close the cover.



4. INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)
  1. Connect the connector.



    B284582
  1. Engage the 9 claws and 4 guides, and install the front armrest base upper panel.



5. INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)
  1. Connect the connector.

    HINT:
    If the armrest base upper panel is equipped with door lock switch, connect the connector.



    B284583
  1. Engage the 6 claws and 3 guides, and install the front armrest base upper panel.



6. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B271669E01
  1. Install the window regulator handle plate.
    Text in Illustration 
    *a
    Inside of Vehicle

  1. Open all the windows.



    B284599E01
  1. Install the front door window regulator handle assembly with the clip at the angle shown in the illustration.
    Text in Illustration 
    *a
    Assemble with Glass in Fully Open Position



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. INSPECT SRS WARNING LIGHT
(Click here)


9. INSPECT POWER WINDOW OPERATION