Home › Engine / Hybrid System › 1NZ-FE INTAKE / EXHAUST › EXHAUST PIPE (for Sedan)

EXHAUST PIPE (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


A104634
  1. Using vernier calipers, measure the free length of the compression spring.

    Minimum length (Front side):
    40.5 mm (1.594 in.)

    Minimum length (Rear side):
    38.5 (1.516 in.)

    If the length is not as specified, replace the compression spring.



    A104635E01
  1. Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.

    NOTICE:
    1. Install the exhaust pipe gasket in the correct direction.
    2. Do not damage the outer surface of the exhaust pipe gasket.
    3. Do not reuse the exhaust pipe gasket.
    4. Do not push in the gasket with the exhaust pipe when connecting it.

  1. Install the 3 No. 4 exhaust pipe supports and front exhaust pipe assembly.



  1. Install the exhaust front pipe assembly and a new exhaust pipe gasket with the 4 compression springs and 4 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A143275



2. INSTALL EXHAUST TAIL PIPE ASSEMBLY


A137397E01
  1. Check the No. 4 exhaust pipe supports.

    NOTICE:
    Install No. 4 exhaust pipe support onto the pipe retaining support.



  1. Install the 3 No. 4 exhaust pipe supports and the exhaust tail pipe assembly.


    A143274

  1. Install the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



3. INSTALL HEATED OXYGEN SENSOR


A115424E02
  1. Using SST, install the heated oxygen sensor onto the front exhaust pipe.

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. This torque value is effective when SST is parallel to the torque wrench.
    2. The "with SST" torque value is effective when using SST with a fulcrum length of 30 mm (1.18 in.).
    3. The "with SST" torque value is effective when using a torque wrench with a fulcrum length of 300 mm (11.81 in.).
    4. If using a torque wrench with a different length, or connecting the torque wrench and SST at an angle, refer to the alternate torque values (Click here).

  1. Pass the sensor connector through the floor panel and install the grommet.

  1. Connect the sensor connector.



4. INSTALL LOWER INSTRUMENT PAD LH
  1. Engage the claw and 3 clips and install the instrument pad lower.

  1. Install the <H> screw.



5. INSTALL CONSOLE BOX ASSEMBLY


    B132349
  1. Engage the 4 claws and install the rear console box.

  1. Install the 2 bolts and 2 screws.

  1. Connect the clamp.



6. INSTALL CONSOLE BOX CARPET


    B132346
  1. Install the console box carpet.



7. INSTALL CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY


    B132348
  1. Connect the connector.

  1. Engage the 3 clips and 3 claws and install the console upper rear panel.



8. INSTALL CONSOLE BOX UPPER PANEL SUB-ASSEMBLY


    B132347
  1. Engage the 5 clips and the claw and install the upper console panel.



9. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132388
  1. Install the shift lever knob.



10. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Engage the 6 claws and 3 clips and install the instrument panel finish panel end LH.



11. INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL


B132316
  1. Engage the 2 claws and 2 clips and install the instrument panel finish panel lower center.



12. INSPECT FOR EXHAUST GAS LEAK