Home › Engine / Hybrid System › 1NZ-FE INTAKE / EXHAUST › EXHAUST MANIFOLD (for Sedan)

EXHAUST MANIFOLD (for Sedan) > REMOVAL

for Preparation Click here



1. REMOVE INSTRUMENT PANEL LOWER CENTER FINISH PANEL


B132316
  1. Disengage the 2 claws and 2 clips and remove the instrument panel finish panel lower center.



2. REMOVE INSTRUMENT PANEL FINISH PANEL END LH


B132317
  1. Disengage the 6 claws and 3 clips and remove the instrument panel finish panel end LH.



3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B132387
  1. Remove the shift lever knob.



4. REMOVE CONSOLE BOX UPPER PANEL SUB-ASSEMBLY


    B132347
  1. Shift the shift lever into the N position.

  1. Disengage the 5 clips and the claw and remove the upper console panel.



5. REMOVE CONSOLE BOX UPPER REAR PANEL SUB-ASSEMBLY


    B132348
  1. Disengage the 3 clips and 3 claws.

  1. Disconnect the connector and remove the console upper rear panel.



6. REMOVE CONSOLE BOX CARPET


B132346
  1. Remove the console box carpet.



7. REMOVE CONSOLE BOX ASSEMBLY


    B132349
  1. Disconnect the clamp.

  1. Remove the 2 bolts and 2 screws.

  1. Disengage the 4 claws and remove the rear console box.



8. REMOVE LOWER INSTRUMENT PAD LH


    B132339
  1. Remove the <H> screw.

  1. Disengage the claw and 3 clips and remove the instrument pad lower.



9. REMOVE FRONT WIPER ARM HEAD CAP


    E127832E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.



10. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E127833
  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.

  1. Remove the nut and front wiper arm.



11. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E127834E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.



13. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127838
  1. Disengage the 3 clips, the 4 claws and the 8 hooks.

  1. Remove the cowl top ventilator louver sub-assembly.



    E127839
  1. Disconnect the washer hoses.

  1. Disengage the 5 hooks.



15. REMOVE FRONT WIPER MOTOR AND LINK


    E127837
  1. Remove the 2 bolts.

  1. Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.



16. REMOVE FRONT AIR SHUTTER SEAL


A133324
  1. Disengage the 3 claws and remove the front air shutter seal RH.



17. REMOVE OUTER COWL TOP PANEL


    A128446
  1. Disengage the wire harness clamp.



    A128447
  1. Remove the 2 bolts and remove the cowl top to cowl inner brace.



    A128448
  1. Remove the 8 bolts and remove the cowl top panel outer.



18. REMOVE HEATED OXYGEN SENSOR
  1. Disconnect the sensor connector.

  1. Remove the grommet and pass the sensor connector out of the cabin through the floor panel.



    A115424E02
  1. Using SST, remove heated oxygen sensor.

    SST
    09224-00010  



19. REMOVE EXHAUST TAIL PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.



  1. Remove the 3 No. 4 exhaust pipe supports and the exhaust tail pipe assembly.


    A143274



20. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.



  1. Remove 3 No. 4 exhaust pipe support and the front exhaust pipe assembly.


    A143275

  1. Remove the 2 exhaust pipe gaskets.



21. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


A166743
  1. Remove the 4 bolts and remove the No. 1 exhaust manifold heat insulator.



22. REMOVE MANIFOLD SUPPORT BRACKET


A143272
  1. Remove the 3 bolts and remove the manifold support bracket.



23. REMOVE EXHAUST MANIFOLD


A254827
  1. Remove the 2 nuts and 3 bolts and remove the exhaust manifold.