Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for Sedan)

BRAKE MASTER CYLINDER (for Sedan) > INSTALLATION

for Preparation Click here



1. INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD


G028332E07
  1. Set SST on the master cylinder sub-assembly and lower the rod of SST until it just touches the piston.
    Text in Illustration 
    *1
    Chalk

    SST
    09737-00013  

    HINT:
    SST: 09737-00012 can also be used.

  1. Apply chalk to the flat tip of the SST rod. Turn SST upside down and measure the clearance between the brake booster push rod and SST.

    Standard clearance:
    -0.21 to 0 mm (-0.00827 to 0 in.)

    If there is clearance between the SST main body and the shell of the brake booster, the push rod is protruding too far. If the chalk does not stick to the tip of the brake booster push rod, the push rod protrusion is insufficient.



    F047969E04
  1. If the clearance is not within the standard, adjust the length by holding the rod using SST and turning the tip of the rod using a 7 mm socket driver.

    SST
    09737-00020  

    NOTICE:
    Check the push rod clearance again after adjusting.



2. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)
  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. Install the brake master cylinder sub-assembly with the 2 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Using a 10 mm union nut wrench, install the 2 brake tubes to the brake master cylinder sub-assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the brake fluid level warning switch connector.



3. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS)
  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. Install the brake master cylinder sub-assembly and the brake tube way with the 2 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Using a 10 mm union nut wrench, install the 5 brake tubes to the brake master cylinder sub-assembly and the brake tube way.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the brake fluid level warning switch connector.



4. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)
  1. Connect the clutch reservoir tube with the clip.



5. INSTALL BATTERY CARRIER
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Install the clamp.



6. INSTALL BATTERY TRAY


7. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



9. FILL RESERVOIR WITH BRAKE FLUID


C241208
  1. Disengage the 3 clips and separate the hood to cowl top seal.

  1. Remove the cowl top ventilator louver.



    C241209
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



10. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C274940
  1. Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the master cylinder.



    C121826
  1. Slowly depress the brake pedal and hold it there (Step A).



    C121827
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat step A and B 3 or 4 times.



    C274940
  1. Using a 10 mm union nut wrench, connect the 2 brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



11. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat step C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



12. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



13. INSPECT FOR BRAKE FLUID LEAK