Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for Sedan)

BRAKE MASTER CYLINDER (for Sedan) > REMOVAL


NOTICE:
Release the vacuum from booster by depressing the brake pedal several times.
Then remove the brake master cylinder from brake booster.



1. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE BATTERY
  1. Disconnect the cable from the battery terminal.

  1. Loosen the nut and remove the battery clamp.

  1. Remove the battery.



4. REMOVE BATTERY TRAY


5. REMOVE BATTERY CARRIER


A117309
  1. Separate the wire harness clamp from the battery carrier.

  1. Remove the 5 bolts and remove the battery carrier.



6. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)


C215148
  1. Slide the clip and disconnect the clutch reservoir tube.



7. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)
  1. Disconnect the brake fluid level warning switch connector.



    C274940
  1. Using a 10 mm union nut wrench , separate the 2 brake tubes from the brake master cylinder sub-assembly.



    C116934
  1. Remove the 2 nuts and the brake master cylinder sub-assembly.

  1. Remove the O-ring from the brake master cylinder sub-assembly.

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the brake master cylinder sub-assembly to receive any impact, such as from being dropped. Do not reuse a brake master cylinder sub-assembly that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. Release the vacuum from the booster by depressing the brake pedal several times. Then remove the brake master cylinder sub-assembly from brake booster.
    4. When installing the brake master cylinder sub-assembly onto the brake booster, or when removing the brake master cylinder sub-assembly from the brake booster, make sure that the brake master cylinder sub-assembly is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling off.
    5. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the piston.
    6. Do not use any other type of grease or fluid.



8. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS)
  1. Disconnect the brake fluid level warning switch connector.



    C274941
  1. Using a 10 mm union nut wrench, separate the 5 brake tubes from the brake tube way and the brake master cylinder sub-assembly.



    C121833
  1. Remove the 2 nuts, brake tube way and the brake master cylinder sub-assembly.

  1. Remove the O-ring from the brake master cylinder sub-assembly.

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the brake master cylinder sub-assembly to receive any impact, such as from being dropped. Do not reuse a brake master cylinder sub-assembly that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. Release the vacuum from the booster by depressing the brake pedal several times. Then remove the brake master cylinder sub-assembly from brake booster.
    4. When installing the brake master cylinder sub-assembly onto the brake booster, or when removing the brake master cylinder sub-assembly from the brake booster, make sure that the brake master cylinder sub-assembly is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling off.
    5. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the piston.
    6. Do not use any other type of grease or fluid.