Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Sedan)

BRAKE BOOSTER (for Sedan) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE VACUUM CHECK VALVE ASSEMBLY
  1. Install the grommet to the brake booster.

  1. Install the brake vacuum check valve assembly to the brake booster.



2. INSTALL BRAKE BOOSTER
  1. Temporarily install the brake master cylinder push rod clevis to the brake booster.

    HINT:
    Tighten the push rod lock nut when adjusting the brake pedal height.

  1. Install a new gasket to the brake booster.

  1. Install the brake booster with the 4 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the vacuum hose to the brake vacuum check valve assembly with the clip.



3. INSTALL BRAKE TUBE (w/o ABS)
  1. Using a 10 mm union nut wrench, install the brake tubes to the proportioning valve.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 10 mm union nut wrench, install the 2 brake tubes to the No. 1 brake tube way.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the push rod pin.



    C116880
  1. Install the push rod clevis with the push rod pin and clip.

  1. Install the brake pedal return spring.



5. INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD


G028332E07
  1. Set SST on the master cylinder sub-assembly and lower the rod of SST until it just touches the piston.
    Text in Illustration 
    *1
    Chalk

    SST
    09737-00013  

    HINT:
    SST: 09737-00012 can also be used.

  1. Apply chalk to the flat tip of the SST rod. Turn SST upside down and measure the clearance between the brake booster push rod and SST.

    Standard clearance:
    -0.21 to 0 mm (-0.00827 to 0 in.)

    If there is clearance between the SST main body and the shell of the brake booster, the push rod is protruding too far. If the chalk does not stick to the tip of the brake booster push rod, the push rod protrusion is insufficient.



    F047969E04
  1. If the clearance is not within the standard, adjust the length by holding the rod using SST and turning the tip of the rod using a 7 mm socket driver.

    SST
    09737-00020  

    NOTICE:
    Check the push rod clearance again after adjusting.



6. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)
  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. Install the brake master cylinder sub-assembly with the 2 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Using a 10 mm union nut wrench, install the 2 brake tubes to the brake master cylinder sub-assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the brake fluid level warning switch connector.



7. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS)
  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. Install the brake master cylinder sub-assembly and the brake tube way with the 2 nuts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Using a 10 mm union nut wrench, install the 5 brake tubes to the brake master cylinder sub-assembly and the brake tube way.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the brake fluid level warning switch connector.



8. CONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)
  1. Connect the clutch reservoir tube with the clip.



9. INSTALL BRAKE ACTUATOR ASSEMBLY (w/ ABS)


    C168356E01
  1. Install the brake actuator assembly with brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not damage the brake tubes or wire harness.



    C241446E01
  1. Temporarily install each brake tube in the correct positions of the brake actuator assembly as shown in the illustration.
    Text in Illustration 
    *a
    to Front Wheel Cylinder RH
    *b
    to Front Wheel Cylinder LH
    *c
    to Rear Wheel Cylinder RH
    *d
    to Rear Wheel Cylinder LH
    *e
    from 1st Master Cylinder
    *f
    from 2nd Master Cylinder

  1. Using a 10 mm union nut wrench, install the 6 brake tubes to the brake actuator assembly.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



    C228100E02
  1. Connect the brake actuator connector.
    Text in Illustration 
    *1
    Lock Lever

    NOTICE:
    1. Make sure that the connector is locked securely.
    2. Make sure that the actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.



10. INSTALL BATTERY CARRIER
  1. Install the battery carrier with the 5 bolts.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Install the clamp.



11. INSTALL BATTERY TRAY


12. INSTALL BATTERY
  1. Install the battery onto the vehicle with the battery clamp.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the cable to the battery terminal.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
  1. Install the 2 <A> screws.

  1. Engage the 7 claws and install the instrument panel lower finish panel.



14. INSTALL COWL TOP PANEL OUTER
  1. Install the cowl top panel outer with the 8 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Install the cowl top to cowl inner brace with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the wire harness clamp.



15. INSTALL FRONT AIR SHUTTER SEAL
  1. Engage the 3 claws to install the front air shutter seal RH.



16. INSTALL FRONT WIPER MOTOR AND LINK


    E127840
  1. Connect the connector.

  1. Slide the wiper link as shown in the illustration and engage the rubber pin with the body.

  1. Install the front wiper motor and link with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



17. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E127839
  1. Connect the washer hoses.

  1. Engage the 5 hooks.



    E127838
  1. Engage the 8 hooks and the 4 claws.

  1. Install the cowl top ventilator louver sub-assembly with the 3 clips.



18. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY LH


    E129651
  1. Engage the 3 claws and install the cowl side ventilator sub-assembly LH.



19. INSTALL COWL SIDE VENTILATOR SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



20. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E113862E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



21. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E058837E10
  1. Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).

  1. Clean the wiper pivot serrations with a wire brush.

  1. Operate the wiper, then stop the windshield wiper motor in the automatic stop position.



    E129694E01
  1. Align the blade tip with the mark on the windshield glass, as shown in the illustration.

  1. Tighten the nut of the front wiper arm.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



22. INSTALL FRONT WIPER ARM HEAD CAP


    E127841
  1. Engage the claw and install the 2 front wiper arm head caps.



23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



24. FILL RESERVOIR WITH BRAKE FLUID


C241208
  1. Disengage the 3 clips and separate the hood to cowl top seal.

  1. Remove the cowl top ventilator louver.



    C241209
  1. Set the brake fluid can upside down on the reservoir.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



25. BLEED MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air from the master cylinder.



    C274940
  1. Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the master cylinder.



    C121826
  1. Slowly depress the brake pedal and hold it there (Step A).



    C121827
  1. Block the outer holes with your fingers, and release the brake pedal (Step B).

  1. Repeat step A and B 3 or 4 times.



    C274940
  1. Using a 10 mm union nut wrench, connect the 2 brake tubes to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



26. BLEED BRAKE LINE


C116913
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (Step C).

  1. At the point where the fluid stops coming out, tighten the bleeder plug, then release the brake pedal (Step D).

  1. Repeat step C and D until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



27. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



28. INSPECT FOR BRAKE FLUID LEAK


29. INSPECT AND ADJUST BRAKE PEDAL


C116874E01
  1. Inspect the brake pedal height.

    Pedal height from floor panel:
    w/ ABS
    w/o ABS
    113.1 to 123.1 mm
    (4.45 to 4.85 in.)
    107.8 to 117.8 mm
    (4.244 to 4.638 in.)

    If the pedal height is incorrect, adjust it.



  1. Adjust the brake pedal height.

    1. Disconnect the connector from the stop light switch.

    2. Turn the stop light switch counterclockwise, and remove the stop light switch.

    3. Loosen the push rod lock nut.

    4. Adjust the pedal height by turning the pedal push rod.

      Pedal height from floor panel:
      w/ ABS
      w/o ABS
      113.1 to 123.1 mm
      (4.45 to 4.85 in.)
      107.8 to 117.8 mm
      (4.244 to 4.638 in.)

    5. Tighten the push rod lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }



    6. F049043E01
    7. Insert the stop light switch into the adjuster until it just touches the brake pedal.

      NOTICE:
      Do not depress the brake pedal.



    8. F049044E08
    9. Make a quarter turn clockwise to install the stop light switch.

      NOTICE:
      Do not depress the brake pedal.

      HINT:
      The turning torque for installing the stop light switch:

      Torque:
      1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    10. Check the stop light switch clearance.

      Stop light switch clearance:
      0.5 to 2.6 mm (0.020 to 0.102 in.)

    11. Connect the connector to the stop light switch.



    F048932E01
  1. Inspect the brake pedal free play.

    1. Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.

    2. Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

      Pedal free play:
      1.0 to 6.0 mm (0.039 to 0.236 in.)

      If incorrect, troubleshoot the brake system.



    R000934E02
  1. Inspect the brake pedal reserve distance.

    1. Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

      Pedal reserve distance from floor panel at 294 N (30 kgf, 66.1 lbf):
      w/ ABS
      w/o ABS
      More than 78 mm (3.07 in.)
      More than 70 mm (2.75 in.)

      HINT:
      Sound and resistance from the brake booster when the brake pedal is depressed without a vacuum does not indicate a problem.

      If incorrect, troubleshoot the brake system.