BRAKE BOOSTER (for Sedan) > REMOVAL |
| 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 2. DRAIN BRAKE FLUID |
| 3. REMOVE FRONT WIPER ARM HEAD CAP |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the 2 front wiper arm head caps.
| 4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Operate the wiper, then stop the windshield wiper motor in the automatic stop position.
Remove the nut and front wiper arm.
| 5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
| 6. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY LH |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the cowl side ventilator sub-assembly LH.
| 7. REMOVE COWL SIDE VENTILATOR SUB-ASSEMBLY RH |
| 8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Disengage the 3 clips, the 4 claws and the 8 hooks.
Remove the cowl top ventilator louver sub-assembly.
![]() |
Disconnect the washer hoses.
Disengage the 5 hooks.
| 9. REMOVE FRONT WIPER MOTOR AND LINK |
![]() |
Remove the 2 bolts.
Slide the wiper link. Disengage the meshing of the rubber pin, then disconnect the connector and remove the front wiper motor and link.
| 10. REMOVE FRONT AIR SHUTTER SEAL |
![]() |
Disengage the 3 claws and remove the front air shutter seal RH.
| 11. REMOVE OUTER COWL TOP PANEL |
![]() |
Disengage the wire harness clamp.
![]() |
Remove the 2 bolts and remove the cowl top to cowl inner brace.
![]() |
Remove the 8 bolts and remove the cowl top panel outer.
| 12. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY |
![]() |
Disengage the 7 claws and open the instrument panel lower finish panel.
![]() |
Remove the 2 <A> screws and the instrument panel lower finish panel.
| 13. REMOVE BATTERY |
Disconnect the cable from the battery terminal.
Loosen the nut and remove the battery clamp.
Remove the battery.
| 14. REMOVE BATTERY TRAY |
| 15. REMOVE BATTERY CARRIER |
![]() |
Separate the wire harness clamp from the battery carrier.
Remove the 5 bolts and remove the battery carrier.
| 16. REMOVE BRAKE ACTUATOR ASSEMBLY (w/ ABS) |
![]() |
Release the lock lever and disconnect the brake actuator connector.
| *1 | Lock Lever |
![]() |
Using a 10 mm union nut wrench, separate the 6 brake tubes from the brake actuator assembly.
![]() |
Use tags or labels to identify the place to reconnect each brake tube.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from 1st Master Cylinder |
| *f | from 2nd Master Cylinder |
![]() |
Remove the 3 bolts and the brake actuator assembly with brake actuator bracket assembly.
| 17. DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle) |
![]() |
Slide the clip and disconnect the clutch reservoir tube.
| 18. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS) |
Disconnect the brake fluid level warning switch connector.
![]() |
Using a 10 mm union nut wrench , separate the 2 brake tubes from the brake master cylinder sub-assembly.
![]() |
Remove the 2 nuts and the brake master cylinder sub-assembly.
Remove the O-ring from the brake master cylinder sub-assembly.
| 19. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS) |
Disconnect the brake fluid level warning switch connector.
![]() |
Using a 10 mm union nut wrench, separate the 5 brake tubes from the brake tube way and the brake master cylinder sub-assembly.
![]() |
Remove the 2 nuts, brake tube way and the brake master cylinder sub-assembly.
Remove the O-ring from the brake master cylinder sub-assembly.
| 20. SEPARATE BRAKE MASTER CYLINDER PUSH ROD CLEVIS |
![]() |
Remove the brake pedal return spring.
Remove the clip and the push rod pin and separate the push rod clevis from the brake pedal.
| 21. REMOVE BRAKE TUBE (w/o ABS) |
![]() |
Using a 10 mm union nut wrench, separate the 2 brake tubes from the No. 1 brake tube way.
![]() |
Using a 10 mm union nut wrench, remove the brake tubes from the proportioning valve.
| 22. REMOVE BRAKE BOOSTER |
![]() |
Slide the clip and disconnect the vacuum hose from the brake vacuum check valve assembly.
![]() |
Remove the 4 nuts and the brake booster.
Remove the gasket from the brake booster.
Loosen the push rod lock nut and remove the brake master cylinder push rod clevis.
| 23. REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY |
![]() |
Remove the brake vacuum check valve assembly from the brake booster.
Remove the grommet from the brake booster.