METER / GAUGE SYSTEM (for Sedan) > Warning Buzzer does not Sound |

| 1.CHECK BUZZER (SEAT BELT, KEY REMINDER, TAILLIGHT REMINDER) |
Check that the seat belt, key reminder and taillight reminder warning buzzers sound.
| Result | Proceed to |
| Seat belt warning buzzer does not sound (where equipped with seat belt warning system) | A |
| Key reminder warning buzzer does not sound (where equipped with key reminder warning system) | B |
| Taillight reminder warning buzzer does not sound (Meter illuminations normal) | C |
| No warning buzzers sound | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK SUPPLEMENTAL RESTRAINT SYSTEM |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.
| Result | Proceed to |
| No SRS DTCs are output | A |
| SRS DTCs are output | B |
|
| ||||
| A | |
| 3.CHECK OCCUPANT CLASSIFICATION SYSTEM |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Body Electrical / Occupant Detection / Trouble Codes.
| Result | Proceed to |
| No occupant classification system DTCs are output | A |
| Occupant classification system DTCs are output | B |
|
| ||||
| A | |
| 4.CHECK KEY REMINDER FUNCTION |
Ignition switch is OFF.
Key is in ignition key cylinder.
Driver side door is open.
|
| ||||
| NG | ||
| ||
| 5.READ VALUE USING TECHSTREAM (FRONT DOOR COURTESY SWITCH (DRIVER SIDE)) |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the item below from the Data List, and read the value displayed on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Driver side door courtesy switch signal / ON or OFF | ON: Driver door is open OFF: Driver door is closed | - |
|
| ||||
| OK | |
| 6.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the item below from the Data List, and read the value displayed on the Techstream.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Key Unlock Warning SW | Unlock warning switch signal / ON or OFF | ON: Key is in ignition key cylinder OFF: No key is in ignition key cylinder | - |
|
| ||||
| NG | |
| 7.INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
![]() |
Disconnect the D19 unlock warning switch assembly connector.
Remove the unlock warning switch assembly.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Not pushed | 10 k Ω or higher |
| 1 - 2 | Pushed | Below 1 Ω |
Reconnect the unlock warning switch assembly.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU) |
![]() |
Disconnect the D19 unlock warning switch connector.
Disconnect the 4D main body ECU connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| D19-1 - 4D-7 (KSW) | Below 1 Ω |
| D19-2 - Body ground | Below 1 Ω |
Reconnect the unlock warning switch connector.
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||
| 9.INSPECT FRONT DOOR COURTESY SWITCH (DRIVER SIDE) |
![]() |
Disconnect the J2 front door courtesy switch connector.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J2-1 - Body ground | Not pushed (ON) | Below 1 Ω |
| J2-1 - Body ground | Pushed (OFF) | 10 kΩ or higher |
Reconnect the front door courtesy switch connector.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH - MAIN BODY ECU) |
![]() |
Disconnect the J2 front door courtesy switch connector.
Disconnect the 4A main body ECU connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| J2-1 - 4A-21 (DCTY) | Below 1 Ω |
Reconnect the front door courtesy switch connector.
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||
| 11.READ VALUE USING TECHSTREAM (FRONT DOOR COURTESY SWITCH) |
Connect the Techstream to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Select the item below from the Data List, and read the value displayed on the Techstream.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Driver door courtesy switch signal / ON or OFF | ON: Driver door is open OFF: Driver door is closed | - |
|
| ||||
| OK | ||
| ||
| 12.INSPECT FRONT DOOR COURTESY SWITCH (DRIVER SIDE) |
![]() |
Disconnect the J2 front door courtesy switch assembly connector.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J2-1 - Body ground | Not pushed (ON) | Below 1 Ω |
| J2-1 - Body ground | Pushed (OFF) | 10kΩ or higher |
Reconnect the front door courtesy switch connector.
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY SWITCH - MAIN BODY ECU) |
![]() |
Disconnect the J2 front door courtesy switch connector.
Disconnect the 4A main body ECU connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| J2-1 - 4A-21 (DCTY) | Below 1 Ω |
Reconnect the front door courtesy switch connector.
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||