FRONT WIPER MOTOR (for Hatchback) > INSTALLATION |
| 1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY |
Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.
Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.
![]() |
Connect the windshield wiper link rod to the crank arm pivot of the windshield wiper motor assembly.
| *1 | Windshield Wiper Link Rod |
| *a | Crank Arm Pivot of the Windshield Wiper Motor Assembly |
| 2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Connect the connector.
Engage the grommet as shown in the illustration.
Install the windshield wiper motor and link assembly with the 2 bolts in the order shown in the illustration.
| 3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
Engage the 9 guides.
Engage the 5 claws and 3 guides to install the cowl top ventilator louver sub-assembly.
Install the 2 clips.
![]() |
Connect the washer hose.
| *a | Tape |
| *b | Clamp |
Engage the 2 clamps.
| 4. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
Using a piece of cloth or similar material, rub off any double-sided tape remaining on the windshield glass.
Using a non-residue solvent, clean the attachment surface.
Remove the double-sided tape backing of a new front fender to cowl side seal LH.
Engage the clip and guide.
Engage the claw and guide to install the front fender to cowl side seal LH.
| 5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
| 6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY |
![]() |
Scrape any metal powder off the serrated part of the wiper arm with a round file or the equivalent (when reinstalling).
| *a | Wire Brush |
| *b | Wiper Arm Serration |
| *c | Wiper Pivot Serration |
Clean the wiper arm serrations.
Clean the wiper pivot serrations with a wire brush.
![]() |
Install the front wiper sub arm.
| *a | Pivot of Front Wiper Sub Arm |
![]() |
Install the front wiper arm and blade assembly with the nut to the position as shown in the illustration.
| *a | Mark for Blade Position |
| Mark | Measurement |
| a | 10 mm (0.394 in.) |
Type A:
![]() |
Align the rib of the washer hose with the rib of the washer nozzle sub-assembly and connect them.
| *a | Rib |
![]() |
| *a | Rib |
![]() |
| *1 | Washer Nozzle Sub-assembly |
| *2 | Washer Hose Joint |
| *3 | Washer Hose |
| *a | Rib |
Type B:
![]() |
Align the rib of the washer hose with the rib of the washer hose joint and connect them.
| *a | Rib |
![]() |
| *a | Rib |
![]() |
| *1 | Washer Nozzle Sub-assembly |
| *2 | Washer Hose Joint |
| *3 | Washer Hose |
| *a | Rib |
Operate the front wipers while spraying washer fluid onto the windshield. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.
| 7. INSTALL FRONT WIPER ARM HEAD CAP |
Type A:
![]() |
Engage the 3 claws to install the front wiper arm head cap.
Type B:
Engage the claw and rotate the front wiper arm head cap.

Engage the 3 claws to install the front wiper arm head cap.