Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR (for Hatchback)

FRONT WIPER MOTOR (for Hatchback) > REMOVAL



1. REMOVE FRONT WIPER ARM HEAD CAP


  1. Type A:



      E273232E03
    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws to remove the front wiper arm head cap.
      Text in Illustration 
      *a
      Protective Tape



  1. Type B:



    1. Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws.


      E263512E01


      Text in Illustration 
      *a
      Protective Tape
      -
      -

    2. While rotating the front wiper arm head cap, disengage the claw to remove the front wiper arm head cap.



2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY


  1. Type A:



      E228992
    1. Disconnect the washer hose.



  1. Type B:



      E271677
    1. Disconnect the washer hose.



    E228993E01
  1. Remove the nut and the front wiper main arm.
    Text in Illustration 
    *1
    Front Wiper Main Arm



    E258165E02
  1. Apply protective tape to the areas shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    E258166E02
  1. Twist a rope around the front wiper sub arm at the area shown in the illustration and pull the rope upward to disengage and remove the front wiper arm and blade assembly.
    Text in Illustration 
    *a
    Head of the Front Wiper Sub Arm
    *b
    Rope

    NOTICE:
    1. If you forcibly disengage the front wiper sub arm in the incorrect direction, it could be deformed or damaged.
    2. If you forcibly pry off the front wiper main arm or front wiper sub arm, the joint section on the end of the front wiper arm could be deformed or damaged.



3. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    E263509E01
  1. Peel off the double-sided tape and disengage the claw and guide.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Disengage the clip and claw to remove the front fender to cowl side seal LH.



4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure as for the LH side.



5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E228995
  1. Disconnect the washer hose.

  1. Disengage the 2 clamps.



    E228997
  1. Remove the 2 clips.

  1. Disengage the 5 claws and 3 guides.

  1. Disengage the 9 guides to remove the cowl top ventilator louver sub-assembly.



6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E228998
  1. Remove the 2 bolts.

  1. Disengage the grommet to remove the windshield wiper motor and link assembly as shown in the illustration.

  1. Disconnect the connector.



7. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY


    E228999E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the windshield wiper link rod from the crank arm pivot of the windshield wiper motor assembly as shown in the illustration.
    Text in Illustration 
    *1
    Windshield Wiper Link Rod
    *a
    Protective Tape
    *b
    Crank Arm Pivot of the Windshield Wiper Motor Assembly



    E263511
  1. Using a T30 "TORX" socket wrench, remove the 2 bolts and the windshield wiper motor assembly from the windshield wiper link assembly.