Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (for Sedan)

FRONT BUMPER (for Sedan) > REASSEMBLY



1. INSTALL FRONT BUMPER ARM SUB-ASSEMBLY LH


    B126350
  1. Insert the 2 location pins into the 2 body holes and install the front bumper arm sub-assembly LH with the 4 bolts.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



2. INSTALL FRONT BUMPER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL WINDSHIELD WASHER JAR ASSEMBLY


    B126351
  1. Insert the location pin into the body hole and install the windshield washer jar assembly with the 2 bolts.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }



4. INSTALL HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL FRONT BUMPER STONE DEFLECTOR BRACKET


    B134818
  1. Install the front bumper stone deflector bracket with the 2 nuts.

    Torque:
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf }

    HINT:
    Use the same procedure as for the opposite side.



6. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    B134817
  1. Install the front bumper reinforcement with the 6 bolts and 4 nuts.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf } for bolt
    5.5 N*m{ 55 kgf*cm , 49 in.*lbf } for nut



7. CONNECT NO. 2 ENGINE ROOM WIRE


    B209578
  1. Engage the 7 claws and install the No. 2 engine room wire.



8. INSTALL RADIATOR SIDE AIR SEAL LH


    B134811
  1. Engage the 4 claws and install the radiator side air seal LH.



9. INSTALL RADIATOR SIDE AIR SEAL RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL THERMISTOR ASSEMBLY (w/ Air Conditioning System)


    B209580
  1. Engage the 2 clamps and install the thermistor assembly.



11. INSTALL RADIATOR SUPPORT UPPER ABSORBER


    B138544
  1. Engage the 6 claws and install the radiator support upper absorber.



12. INSTALL FRONT BUMPER SIDE RETAINER LH


    B134807
  1. Engage the 2 claws and install the front bumper side retainer LH.

  1. Tighten the screw and the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } for bolt



13. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL FRONT BUMPER EXTENSION MOULDING RH


    B134830
  1. Engage the 3 claws and install the front bumper extension moulding RH.



15. INSTALL FRONT BUMPER HOLE COVER LH


    B134829
  1. Engage the 4 claws and install the front bumper hole cover LH.



16. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure as for the LH side.



17. INSTALL FOG LIGHT ASSEMBLY LH


    B134827
  1. Install the fog light assembly LH with the 3 screws.



18. INSTALL FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



19. INSTALL RADIATOR LOWER GRILLE


    B134826
  1. Engage the 12 claws and install the radiator lower grille.



20. INSTALL RADIATOR GRILLE


    B209121
  1. Engage the 13 claws and install the radiator grille.

  1. Install the 2 screws.



21. INSTALL FRONT BUMPER EMBLEM
  1. Engage the 4 claws and install the front bumper emblem.