ENGINE IMMOBILISER SYSTEM (for Hatchback) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Immobiliser / Data List.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door Courtesy SW | Not available / OFF or ON | - | - |
| Key SW | Unlock warning switch signal / OFF or ON | OFF: No key in ignition key cylinder ON: Key inserted in ignition key cylinder | - |
| IG SW*2 | Ignition switch signal / OFF or ON | OFF: Ignition switch ACC or off ON: Ignition switch ON | - |
| Immobiliser*2 | Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset | Set: Engine immobiliser set (engine start prohibited (no key in ignition key cylinder)) Unset: Engine immobiliser unset (engine start permitted (key inserted in ignition key cylinder)) | When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly. |
| Response | Key response to signal from transponder key ECU assembly / OK or NG | OK: Key responds to signal from transponder key ECU assembly NG: Key does not respond to signal from transponder key ECU assembly | Problems may be caused by the following:
|
| Frame Error | State of data sent from key / OK or NG | OK: No problem with data sent from key NG: Problem with data sent from key | Problems may be caused by the following:
|
| Different Serial Number*1 | Vehicle serial number / OK or NG | OK: Signal from transponder chip and vehicle serial number stored in transponder key ECU assembly match NG: Signal from transponder chip and vehicle serial number stored the transponder key ECU assembly do not match | Problems may be caused by the following:
|
| Different Encrypt Code*1 | Code status between transponder chip and transponder key ECU assembly / OK or NG | OK: Codes of transponder chip and transponder key ECU assembly match NG: Codes of transponder chip and transponder key ECU assembly do not match | Problems may be caused by the following:
|
| Abnormal Status*1 | Transponder chip status signal / OK or NG | OK: Transponder chip status signal normal NG: Transponder chip status signal malfunction (malfunction in code computation in key/transponder key ECU assembly) | Problems may be caused by the following:
|
| Bcc Malfunction*1 | Bcc signal status of transponder chip / OK or NG | OK: Bcc signal normal NG: Bcc signal malfunction (malfunction in code computation in key/transponder key ECU assembly) | Problems may be caused by the following:
|
| Sub Key | Whether sub-key ID code matches ID code registered in transponder key ECU assembly / Unreg or Reg | Unreg: ID code of sub-key does not match ID code registered in transponder key ECU assembly Reg: ID code of sub-key matches ID code registered in transponder key ECU assembly | - |
| Master Key | Whether master key ID code matches ID code registered in transponder key ECU assembly / Unreg or Reg | Unreg: ID code of master key does not match ID code registered in transponder key ECU assembly Reg: ID code of master key matches ID code registered in transponder key ECU assembly | - |
| Transponder S-code | Number of registered sub-keys / min.: 0, max.: 15 | Number of registered sub-keys | - |
| Transponder M-code | Number of registered master keys / min.: 0, max.: 15 | Number of registered master keys | - |
| Reg Code Space Full | Key registration code memory space full / No or Yes | Yes: Cannot register any more key codes No: Possible to register more key codes | - |
| +B | +B judgment / Normal or Break | Normal: Battery power supply normal Break: Battery power supply malfunctioning | - |
| Antenna Coil Status | Antenna coil condition / Normal or Fail | Normal: Antenna coil normal Fail: Antenna coil malfunctioning | - |
| EEPROM Status | EEPROM status / OK or NG | OK: Data OK NG: Data error | - |
| E/G Start Permission*2 | Engine start permission / NG or OK | NG: Engine start not permitted OK: Engine start permitted | - |
| Immobi ECU Comm Spd | Immobiliser ECU communication speed / Unknown, 50bps, 200bps or No Res | Unknown: ECU communication speed unknown 50bps: ECU communication speed 50 bps 200bps: ECU communication speed 200 bps No Res: No response regarding ECU communication speed | - |
| The Number of DTCs | Number of DTCs / Min.: 0, Max.: 255 | Number of stored DTCs | - |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Immobiliser Fuel Cut | Status of immobiliser fuel cut / ON or OFF | - | - |
| ACTIVE TEST |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Body Electrical / Immobiliser / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Security Indicator | Theft Warning Indicator Light Assembly | OFF / ON | - |