Home › General › SPECIFICATIONS › 1NZ-FE STARTING (for Hatchback)

1NZ-FE STARTING (for Hatchback) > SERVICE DATA



for Hatchback Except Cold Area Specification Vehicles 
Starter assembly
Battery positive terminal - Terminal 30 - Terminal 50
90 A or less at 11.5 V
Starter relay
Standard resistance
3 - 5
Below 1 Ω(Battery voltage not applied)
Standard resistance
3 - 5
Below 1 Ω(Battery voltage applied to terminals 1 and 2)
Ignition or starter switch assembly.
Standard resistance
Between all terminals
10 kΩ or higher
(LOCK)
Standard resistance
2(ACC) - 4(AM1)
Below 1 Ω
(ACC)
Standard resistance
1(IG1) - 2(ACC) - 4(AM1)
Below 1 Ω
(ON)
Standard resistance
5(AM2) - 6(IG2)
Standard resistance
1(IG1) - 4(AM1)
Below 1 Ω
(START)
Standard resistance
5(AM2) - 6(IG2) - 7(ST2)
Magnet starter switch assembly resistance
Terminal 50 - Body
Below 2 Ω
Starter armature assembly resistance
Segment - Segment
Below 1 Ω
Commutator - Coil core
10kΩ or higher
Starter armature assembly commutator circumference runout
Standard runout
0.02 mm (0.000787 in.)
Maximum runout
0.05 mm (0.00197 in.)
Starter armature assembly commutator diameter
Standard diameter
25.0 mm (0.9843 in.)
Minimum diameter
24.0 mm (0.9449 in.)
Starter armature assembly undercut depth
Standard depth
0.7 mm (0.0276 in.)
Minimum depth
0.2 mm (0.00787 in.)
Starter brush holder assembly Brush length
Standard length
11.6 mm (0.4567 in.)
Minimum length
7.6 mm (0.2992 in.)

for Hatchback for Cold Area Specification Vehicles 
Starter assembly
Battery positive terminal - Terminal 30 - Terminal 50
90 A or less at 11.5 V
Starter relay
Standard resistance
3 - 5
Below 1 Ω(Battery voltage not applied)
Standard resistance
3 - 5
Below 1 Ω(Battery voltage applied to terminals 1 and 2)
Ignition or starter switch assembly.
Standard resistance
Between all terminals
10 kΩ or higher
(LOCK)
Standard resistance
2(ACC) - 4(AM1)
Below 1 Ω
(ACC)
Standard resistance
1(IG1) - 2(ACC) - 4(AM1)
Below 1 Ω
(ON)
Standard resistance
5(AM2) - 6(IG2)
Standard resistance
1(IG1) - 4(AM1)
Below 1 Ω
(START)
Standard resistance
5(AM2) - 6(IG2) - 7(ST2)
Magnet starter switch assembly resistance
Terminal 50 - Terminal C
Below 1 Ω
Terminal 50 - Body ground
Below 2 Ω
Starter armature assembly resistance
Segment - Segment
Below 1 Ω
Commutator - Armature
10kΩ or higher
Starter armature assembly commutator circumference runout
Standard runout
0.02 mm (0.000787 in.)
Maximum runout
0.05 mm (0.00197 in.)
Starter armature assembly commutator diameter
Standard diameter
29.0 mm (1.14 in.)
Minimum diameter
28.0 mm (1.10 in.)
Starter armature assembly undercut depth
Standard depth
0.7 mm (0.0276 in.)
Minimum depth
0.2 mm (0.00787 in.)
Starter brush holder assembly Brush length
Standard length
14.4 mm (0.567 in.)
Minimum length
9.0 mm (0.354 in.)
Starter brush holder assembly resistance
A - B
10 kΩ or higher
A - C
10 kΩ or higher
A - D
Below 1 Ω
B - C
Below 1 Ω
B - D
10 kΩ or higher
C - D
10 kΩ or higher