Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Hatchback Driver Side)

FRONT SEAT ASSEMBLY (for Hatchback Driver Side) > REASSEMBLY


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL SEAT TRACK ADJUSTING HANDLE


    B273286
  1. Engage the 2 hooks to install the seat track adjusting handle to the separate type front seat cushion spring assembly.



2. INSTALL SEAT ADJUSTER COVER CAP


    B349744
  1. Install the 2 seat adjuster cover caps.



3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    B349735
  1. Install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL SEAT CUSHION EDGE PROTECTOR RH (w/ Vertical Adjuster)


    B332526
  1. Engage the claw and guide to install the seat cushion edge protector RH.

  1. Install the screw.



5. INSTALL SEAT CUSHION EDGE PROTECTOR LH (w/ Vertical Adjuster)

HINT:
Use the same procedure as for the RH side.



6. INSTALL SEAT CUSHION EDGE PROTECTOR RH (w/o Vertical Adjuster)


    B332527
  1. Engage the claw and guide to install the seat cushion edge protector RH.

  1. Install the screw.



7. INSTALL SEAT CUSHION EDGE PROTECTOR LH (w/o Vertical Adjuster)

HINT:
Use the same procedure as for the RH side.



8. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH (w/ Vertical Adjuster)


    B273283
  1. Engage the clip to install the front seat cushion lower shield RH.

  1. Install the screw.



    B273289
  1. Engage the hook.



9. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH (w/ Vertical Adjuster)

HINT:
Use the same procedure as for the RH side.



10. INSTALL RECLINING ADJUSTER INSIDE COVER RH (for TMC Made)


    B283246
  1. Engage the guide to install the reclining adjuster inside cover RH.



11. INSTALL RECLINING ADJUSTER INSIDE COVER LH (for TMC Made)

HINT:
Use the same procedure as for the RH side.



12. INSTALL FRONT SEAT CUSHION LOWER SHIELD (w/ Vertical Adjuster)


    B283244
  1. Engage the 2 claws to install the front seat cushion lower shield.



13. INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)


    B332512
  1. Install a new front seat airbag assembly with 2 new nuts.

    CAUTION:
    1. The nuts and front seat airbag assembly must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B283242
  1. Engage the 2 clamps.



14. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for TMC Made)

NOTICE:
  1. For vehicles with front seat airbag assembly, the front seat airbag assembly may not be activated normally unless the separate type front seatback cover is securely installed.
  2. Check that the strap is not twisted after installing the front seatback cover bracket.
  3. Install the front seatback cover bracket securely.



    B272777E03
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the separate type front seatback cover with the center of the separate type front seatback pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for TMMF Made)


    B351899
  1. Engage the 7 hooks to install the separate type front seatback cover to the separate type front seatback pad.



16. INSTALL SEATBACK COVER WITH PAD (for TMC Made)


    B332513
  1. Install the seatback cover with pad to the separate type front setback spring assembly.

  1. Install the front seatback cover bracket with the 2 new nuts. (w/ Front Seat Side Airbag)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with front seat airbag assembly, the front seat airbag assembly may not be activated normally unless the seatback cover with pad is securely installed.
    2. Check that the strap is not twisted after installing the front seatback cover bracket.
    3. Install the front seatback cover bracket securely.



    B272974
  1. Fasten the 2 zippers. (for Sport Package)



    B272765E01
  1. Align the protruding portion of the front seat headrest support with the installation groove of the separate type front seatback spring assembly.
    Text in Illustration 
    *a
    Protruding

  1. Engage the 4 claws to install the 2 front seat headrest supports.



    B284663E02
  1. Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seatback cover.
    2. Securely tighten the hog rings as shown in the illustration.



    B284664E02
  1. Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seatback cover.
    2. Securely tighten the hog rings as shown in the illustration.



17. INSTALL SEATBACK COVER WITH PAD (for TMMF Made)


    B332513
  1. Install the seatback cover with pad to the separate type front setback spring assembly.

  1. Install the front seatback cover bracket with the 2 new nuts. (w/ Front Seat Side Airbag)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with front seat airbag assembly, the front seat airbag assembly may not be activated normally unless the seatback cover with pad is securely installed.
    2. Check that the strap is not twisted after installing the front seatback cover bracket.
    3. Install the front seatback cover bracket securely.



    B272765E01
  1. Align the protruding portion of the front seat headrest support with the installation groove of the separate type front seatback spring assembly.
    Text in Illustration 
    *a
    Protruding

  1. Engage the 4 claws to install the 2 front seat headrest supports.



    B283283
  1. Engage the 2 hooks.



    B351898
  1. Engage the 3 hook.



18. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (for TMC Made)


    B272775E05
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 14 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seat cushion cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the separate type front seat cushion cover with the center of the separate type front seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



    B349746E01
  1. Using hog ring pliers, install the 2 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seat cushion cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.
    3. Securely tighten the hog rings as shown in the illustration.



19. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (for TMMF Made)


    B349731
  1. Engage the 15 hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.



20. INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY (w/ Front Seat Side Airbag)

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.

  1. Install the SRS seat cushion airbag assembly with 3 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the clamps to install the SRS seat cushion airbag wire harness.



21. INSTALL SEAT CUSHION COVER WITH PAD


  1. Engage the 5 hooks to install the seat cushion cover with pad to the separate type front seat cushion spring assembly.


    B349730



    B332533
  1. Engage the 2 hooks.



    B290038
  1. Engage the 3 clamps to install the front seat airbag wire harness. (w/ Front Seat Side Airbag)



    B272761
  1. Engage the 4 hooks.



    B351897
  1. Engage the 2 hooks. (for TMMF Made)



    B289256
  1. Fasten the hook and loop fastener. (w/ Front Seat Side Airbag)



    B332511
  1. Connect the seatback cover band.

  1. Engage the 2 hooks.



22. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B283230
  1. Engage the 2 claws to install the front seat cushion inner shield.



23. INSTALL FRONT SEAT CUSHION SHIELD


    B283229
  1. Engage the clip and 2 claws to install the front seat cushion shield.

  1. Install the screw.



24. INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)


    B283228
  1. Install the vertical adjusting handle with the screw.



25. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B332529
  1. Engage the claw to install the reclining adjuster release handle.



26. INSTALL FRONT SEAT HEADREST ASSEMBLY
  1. Install the front seat headrest assembly.



27. INSTALL FRONT SEAT INNER BELT ASSEMBLY


  1. for 4 Way Seat Type:



      B288269E02
    1. Install the front seat inner belt assembly with the nut.
      Text in Illustration 
      *a
      Convex

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt assembly over the convex areas of the separate type front seat cushion spring assembly.

    2. Engage the clamp.

    3. Engage the 3 clamps.



  1. for 6 Way Seat Type:



      B286794E01
    1. Install the front seat inner belt assembly with the nut.
      Text in Illustration 
      *a
      Convex

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt assembly over the convex areas of the separate type front seat cushion spring assembly.

    2. Engage the 2 clamps.

    3. Engage the 4 clamps.



28. INSTALL FRONT SEAT CUSHION COVER
  1. Engage the 2 hooks to install the front seat cushion cover.

  1. Install the 2 clips.