Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Hatchback Front Passenger Side)

FRONT SEAT ASSEMBLY (for Hatchback Front Passenger Side) > REASSEMBLY


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL SEAT TRACK ADJUSTING HANDLE


    B287806
  1. Engage the 2 hooks to install the seat track adjusting handle to the separate type front seat cushion spring assembly.



2. INSTALL SEAT ADJUSTER COVER CAP


    B349744
  1. Install the 2 seat adjuster cover caps.



3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    B349739
  1. Install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly with the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL SEAT LOCK CONTROL CABLE ASSEMBLY (for 3 Door)


    B287804E01
  1. Engage the 2 cable ends and 2 clamps to install the seat lock control cable assembly.
    Text in Illustration 
    *1
    Clamp
    *2
    Cable End



5. INSTALL SEATBACK CONTROL CABLE ASSEMBLY (for 3 Door)


    B287803E01
  1. Engage the cable end and 3 clamps to install the seatback control cable assembly.
    Text in Illustration 
    *1
    Clamp
    *2
    Cable End



    B287802E02
  1. Engage the nipple end and clamp to install the seatback control cable assembly.
    Text in Illustration 
    *1
    Casing Cap
    *2
    Nipple End
    *3
    Clamp

  1. Install the casing cap.



6. INSTALL SEAT CUSHION EDGE PROTECTOR RH


    B332531
  1. Engage the claw and guide to install the seat cushion edge protector RH.

  1. Install the screw.



7. INSTALL SEAT CUSHION EDGE PROTECTOR LH

HINT:
Use the same procedure as for the RH side.



8. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B287800
  1. Engage the guide to install the reclining adjuster inside cover RH.



9. INSTALL RECLINING ADJUSTER INSIDE COVER LH

HINT:
Use the same procedure as for the RH side.



10. INSTALL RECLINING REMOTE CONTROL BASE (for 3 Door)


    B288454
  1. Engage the 4 guides to install the reclining remote control base.



11. INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)


    B287807
  1. Install a new front seat side airbag assembly with 2 new nuts.

    CAUTION:
    1. The nuts and front seat airbag assembly must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



    B272934
  1. Engage the 2 clamps.



12. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for TMC Made)

NOTICE:
  1. For vehicles with front seat airbag assembly, the front seat airbag assembly may not be activated normally unless the separate type front seatback cover is securely installed.
  2. Check that the strap is not twisted after installing the front seatback cover bracket.
  3. Install the front seatback cover bracket securely.



    B272777E04
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the separate type front seatback cover with the center of the separate type front seatback pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for TMMF Made)


    B351899
  1. Engage the 7 hooks to install the separate type front seatback cover to the separate type front seatback pad.



14. INSTALL SEATBACK COVER WITH PAD (for TMC Made)


    B349738
  1. Install the front seatback cover with pad to the separate type front seatback spring assembly.

  1. Install the front seatback cover bracket with the 2 new nuts. (w/ Front Seat Side Airbag)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with front seat airbag assembly, the front seat airbag assembly may not be activated normally unless the seatback cover with pad is securely installed.
    2. Check that the strap is not twisted after installing the front seatback cover bracket.
    3. Install the front seatback cover bracket securely.



    B272974
  1. Fasten the 2 zippers. (for Sport Package)



    B272765E01
  1. Align the protruding portion of the front seat headrest support with the installation groove of the separate type front setback spring assembly.
    Text in Illustration 
    *a
    Protruding

  1. Engage the 4 claws to install the 2 front seat headrest supports.



    B287798E02
  1. Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seatback cover.
    2. Securely tighten the hog rings as shown in the illustration.



    B287796E02
  1. Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type front seatback cover.
    2. Securely tighten the hog rings as shown in the illustration.



15. INSTALL SEATBACK COVER WITH PAD (for TMMF Made)


    B349738
  1. Install the front seatback cover with pad to the separate type front seatback spring assembly.

  1. Install the front seatback cover bracket with the 2 new nuts. (w/ Front Seat Side Airbag)

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with front seat airbag assembly, the front seat airbag assembly may not be activated normally unless the seatback cover with pad is securely installed.
    2. Check that the strap is not twisted after installing the front seatback cover bracket.
    3. Install the front seatback cover bracket securely.



    B272765E01
  1. Align the protruding portion of the front seat headrest support with the installation groove of the separate type front setback spring assembly.
    Text in Illustration 
    *a
    Protruding

  1. Engage the 4 claws to install the 2 front seat headrest supports.



    B283283
  1. Engage the 2 hooks.



    B351904
  1. Engage the 3 hooks.



16. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY (for 3 Door)


    B332530
  1. Engage the cable end and clamp to connect the reclining remote control lever sub-assembly to the seatback control cable assembly.



    B288408
  1. Install the reclining remote control lever sub-assembly with the 2 screws.



    B332519
  1. Engage the 2 guides and claw to install the cover.



17. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (for TMC Made)


    B272775E06
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 14 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the separate type front seat cushion cover with the center of the separate type front seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



    B349745E01
  1. Using hog ring pliers, install the 2 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.
    3. Securely tighten the hog rings as shown in the illustration.



18. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (for TMMF Made)


    B349731
  1. Engage the 15 hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.



19. INSTALL FRONT SEAT AIRBAG SUB-ASSEMBLY (w/ Front Seat Side Airbag)

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.

  1. Install the SRS seat cushion airbag assembly with 3 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the clamps to install the SRS seat cushion airbag wire harness.



20. INSTALL SEAT CUSHION COVER WITH PAD


  1. Engage the 5 hooks to install the seat cushion cover with pad to the separate type front seat cushion spring assembly.


    B349737



    B349736
  1. Engage the 2 hooks.



    B290782
  1. Engage the 3 clamps to install the front seat side airbag wire harness. (w/ Front Seat Side Airbag)



    B272761
  1. Engage the 4 hooks.



    B351903
  1. Engage the 2 hooks. (for TMMF Made)



    B287792
  1. Fasten the hook and loop fastener. (w/ Front Seat Side Airbag)



    B290781
  1. Connect the seatback cover band.



21. INSTALL FRONT SEAT WIRE


    B288380
  1. Engage the 4 clamps to install the front seat wire.

  1. Connect the 2 connectors.



22. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B272755
  1. Engage the 2 claws to install the front seat cushion inner shield.



23. INSTALL FRONT SEAT CUSHION SHIELD


    B287790
  1. Engage the clip and 2 claws to install the front seat cushion shield.

  1. Install the screw.



24. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B287789
  1. Engage the claw to install the reclining adjuster release handle.



25. INSTALL FRONT SEAT HEADREST ASSEMBLY
  1. Install the front seat headrest assembly.



26. INSTALL OCCUPANT DETECTION ECU


    B288381
  1. Engage the claw to install the occupant detection ECU.

    NOTICE:
    If the occupant detection ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the occupant detection ECU with a new one.

  1. Connect the 2 connectors.

    NOTICE:
    When installing the occupant detection ECU, be careful that the SRS wiring does not interfere with or is pinched between other parts.



27. INSTALL FRONT SEAT INNER BELT ASSEMBLY


  1. w/ Limit Switch:



      B291218E01
    1. Install the front seat inner belt assembly with the nut.
      Text in Illustration 
      *a
      Convex

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt assembly over the convex areas of the separate type front seat cushion spring assembly.

    2. Connect the connector.

    3. Install the front seat cushion inner shield.



  1. w/o Limit Switch:



      B270851E02
    1. Install the front seat inner belt assembly with the nut.
      Text in Illustration 
      *a
      Convex

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

      NOTICE:
      Do not place the front seat inner belt assembly over the convex areas of the separate type front seat cushion spring assembly.

    2. Engage the clamp.

  1. Connect the connector and engage the clamp.

  1. Engage the 2 hooks.