Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type RH Side)

REAR SEAT ASSEMBLY (for Sedan 60/40 Split Seat Type RH Side) > REASSEMBLY


CAUTION:
Wear protective gloves. Sharp surfaces on the rear seatback frame could cause injuries to your hands.



1. INSTALL REAR SEATBACK LOCK ASSEMBLY


    B134965
  1. Install the rear seatback lock with the 2 bolts.

    Torque:
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }



2. INSTALL REAR SEAT BACK COVER (for Cover Separate Type)


    B212254E01
  1. Using hog ring pliers, install the rear seat back cover with 15 new hog rings.

    NOTICE:
    1. Do not soil or scratch the rear seat back cover.
    2. When installing hog hog rings, minimize wrinkles as far as possible.



3. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY


    B134964
  1. Install the rear seatback frame.



    B134961E01
  1. Using hog ring pliers, install 9 new hog rings as shown in the illustration.



4. INSTALL REAR SEAT HEADREST SUPPORT


B134963E01

HINT:
Use the same procedure to install all the rear seat headrest supports.

  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame.

  1. Engage the 2 claws and install the rear seat headrest support.



5. INSTALL CUP HOLDER ASSEMBLY


    B134959
  1. Engage the 4 claws and install the rear seat cup holder.



6. INSTALL REAR SEAT CENTER ARMREST HINGE


    B134958
  1. Install the rear seat armrest hinge with the 2 bolts, the 2 spacers.

    Torque:
    21 N*m{ 215 kgf*cm , 16 ft.*lbf }



7. INSTALL REAR SEAT CENTER ARMREST HINGE COVER


    B134957
  1. Engage the 3 claws and install the rear seat center armrest hinge cover.



8. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    B134956
  1. Install the rear seat center armrest with the 2 nuts and the 2 wave washers.

    Torque:
    33 N*m{ 335 kgf*cm , 24 ft.*lbf }



    B134955
  1. Install the rear seatback cover with the 7 clips.



9. INSTALL REAR SEATBACK LOCK CONTROL BEZEL


    B134954
  1. Engage the 2 claws and install the rear seatback lock control bezel.



10. INSTALL REAR CENTER SEAT SHOULDER BELT GUIDE


    B134952
  1. Insert the pin into the rear seatback frame hole and install the rear center seat shoulder belt guide with the 2 screws.



11. INSTALL REAR SEATBACK LOCK RELEASE BUTTON


    B134953
  1. Install the rear seatback lock release button.



12. INSTALL REAR SEAT SHOULDER BELT GUIDE


    B134950
  1. Insert the pin into the rear seatback frame hole and install the rear seat shoulder belt guide with the 2 screws.



13. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


    B134948E01
  1. Push the lock button of the rear seat headrest support and install the rear seat headrest.



14. INSTALL REAR SEAT HEADREST ASSEMBLY


    B134947E01
  1. Push the lock button of the rear seat headrest support and install the rear seat headrest.



15. INSTALL REAR SEAT CUSHION COVER (for Cover Separate Type)


    B169409E01
  1. Using hog ring pliers, install the rear seat cushion cover with 39 new hog rings.

    NOTICE:
    1. Do not soil or scratch the rear seat cushion cover.
    2. When installing hog rings, minimize wrinkles as far as possible.