Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat Type RH Side)

REAR SEAT ASSEMBLY (for Hatchback 60/40 Split Seat Type RH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.



1. INSTALL SEPARATE TYPE REAR SEATBACK COVER (for TMC Made)


    B283274E02
  1. Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 6 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the separate type rear seatback cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the separate type rear seatback cover with the center of the separate type rear seatback pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



2. INSTALL SEPARATE TYPE REAR SEATBACK COVER (for TMMF Made)


    B283275
  1. Engage the 7 hooks to install the separate type rear seatback cover to the separate type rear seatback pad.



3. INSTALL REAR SEATBACK LOCK ASSEMBLY RH


    B272888
  1. Install the rear seatback lock assembly RH to the rear seatback frame sub-assembly RH with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



4. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH (for TMC Made)


    B272887
  1. Temporarily install the rear seatback frame sub-assembly RH.



    B272885
  1. Engage the 5 hooks.



    B272788
  1. Engage the 7 clips to install the rear seatback frame sub-assembly RH.



5. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH (for TMMF Made)


    B272887
  1. Temporarily install the rear seatback frame sub-assembly RH.



    B272885
  1. Engage the 5 hooks.



    B351901
  1. Fasten the 7 hook and loop fasteners.

  1. Engage the 2 clips to install the rear seatback frame sub-assembly RH.



6. INSTALL REAR SEAT HEADREST SUPPORT


    B273340E01
  1. Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame sub-assembly RH.
    Text in Illustration 
    *a
    Protruding

  1. Engage the 4 claws to install the 2 rear seat headrest supports.



7. INSTALL REAR SEATBACK STOP BUTTON GROMMET


    B272886
  1. Engage the 2 claws to install the rear seatback stop button grommet.



8. INSTALL REAR SEATBACK LOCK RELEASE BUTTON


    B273714
  1. Turn the rear seatback lock release button in the direction indicated by arrow to install it.



9. INSTALL REAR SEATBACK COVER


    B272787
  1. Engage the 4 claws to install the rear seatback cover.



10. INSTALL REAR SEAT HEADREST ASSEMBLY
  1. Install the rear seat headrest assembly.



11. INSTALL BENCH TYPE REAR SEAT CUSHION COVER (for TMC Made)


    B349743E01
  1. Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 44 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *a
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the bench type rear seat cushion cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the bench type rear seat cushion cover with the center of the bench type rear seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



12. INSTALL BENCH TYPE REAR SEAT CUSHION COVER (for TMMF Made)


    B349742
  1. Pass the 3 plastic plates of the bench type rear seat cushion cover through the bench type rear seat cushion pad.

  1. Engage the 30 hooks and install the bench type rear seat cushion cover.