Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR (for Sedan)

LUGGAGE COMPARTMENT DOOR (for Sedan) > INSTALLATION



1. INSTALL LUGGAGE COMPARTMENT DOOR WEATHERSTRIP


B140676
  1. Install the luggage compartment door weatherstrip.



2. INSTALL LUGGAGE COMPARTMENT TRIM INNER PAD


    B136275
  1. Install the luggage compartment trim inner pad.



3. INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER RH


    B349026
  1. Install the luggage compartment trim cover inner RH with the 5 clips.



4. INSTALL LUGGAGE COMPARTMENT TRIM COVER INNER LH

HINT:
Use the same procedure as described for the RH side.



5. INSTALL REAR FLOOR FINISH PLATE


    B349025
  1. Engage the 8 claws and install the rear floor finish plate.

  1. Install the 2 clips.



6. INSTALL DECK FLOOR BOX RH


    B136273
  1. Install the deck floor box RH.



7. INSTALL DECK FLOOR BOX LH

HINT:
Use the same procedure as described for the RH side.



8. INSTALL SPARE WHEEL COVER ASSEMBLY


    B136270
  1. Install the spare wheel cover assembly.



9. INSTALL SYMBOL EMBLEM


    B126358E01
  1. Clean the attachment surface.
    Text in Illustration 
    *a
    Peeling Paper
    *b
    Location Pin

    1. Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the symbol emblem while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Align the 2 location pins and install a new symbol emblem.

    NOTICE:
    Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.



10. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


    B134867E03
  1. Clean the attachment surface.
    Text in Illustration 
    *a
    Peeling Paper
    *b
    Outside Line of Luggage Compartment Door Panel

    1. Using an infrared light, heat the double-sided tape remaining on the luggage compartment door panel.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the remaining double-sided tape off the luggage compartment door panel while it is hot from the infrared light.

      NOTICE:
      Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the luggage compartment door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.

  1. Install a new No. 2 luggage compartment door name plate as shown in the illustration.

    Installation Position:
    Mark
    Measurement (along surface)
    a
    39.4 mm (1.551 in.)
    b
    44.7 mm (1.760 in.)
    c
    162.4 mm (6.394 in.)
    d
    17.8 mm (0.701 in.)

    NOTICE:
    Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the luggage compartment door panel and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



11. INSTALL LICENSE PLATE LIGHT ASSEMBLY


E127156
  1. Install the license plate light bulb into the light socket.

  1. Turn the license plate light bulb socket and bulb, in the directions indicated by the arrow in the illustration, to install them.



    E125504E01
  1. Engage claw A and claw B, and install the license plate light assembly.



12. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    B134844
  1. Engage the 3 clips and install the luggage compartment door outside garnish.

  1. Tighten the 2 nuts.



13. INSTALL DOOR UNLOCK SWITCH


    B144407
  1. Engage the 2 claws and install the door unlock switch.



14. INSTALL LUGGAGE COMPARTMENT LOCK CYLINDER


    B144408
  1. Install the luggage compartment lock cylinder with the 2 nuts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. Engage the snap and connect the luggage compartment door lock link.

  1. Connect the connector.



15. INSTALL LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    E129673
  1. Install the luggage door lock control cable.

  1. Install the luggage compartment door lock assembly with the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 48 in.*lbf }



    E129675
  1. Connect the connector.

  1. Engage the claw and install the protector lid.



    E127151
  1. Install the luggage compartment door lock link.



16. INSTALL LUGGAGE COMPARTMENT DOOR COVER


B349024
  1. Install the luggage compartment door cover with the 11 clips.