Home › Vehicle Exterior › DOOR / HATCH › LUGGAGE COMPARTMENT DOOR (for Sedan)

LUGGAGE COMPARTMENT DOOR (for Sedan) > DISASSEMBLY



1. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    B349024
  1. Remove the 11 clips and the luggage compartment door cover.



2. REMOVE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    E127146
  1. Remove the snap ring in the direction indicated by the arrow and remove the luggage compartment door lock link.



    E129672
  1. Disconnect the connector.

  1. Disengage the claw and pull up the protector lid in the direction indicated by the arrow.



    E129673
  1. Remove the luggage door lock control cable.

  1. Remove the 2 bolts and the luggage compartment door lock assembly.



3. REMOVE LUGGAGE COMPARTMENT LOCK CYLINDER
  1. Disconnect the connector.



    B144406
  1. Disengage the snap and disconnect the luggage compartment door lock link as shown in the illustration.

  1. Remove the 2 nuts and the luggage compartment lock cylinder.



4. REMOVE DOOR UNLOCK SWITCH


    B144407
  1. Disengage the 2 claws and remove the door unlock switch.



5. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY


    B134844
  1. Remove the 2 nuts.

  1. Disengage the 3 clips and remove the luggage compartment door outside garnish.



6. REMOVE LICENSE PLATE LIGHT ASSEMBLY


E125503E01
  1. Pull the license plate light assembly in the direction indicated by arrow 1, shown in the illustration. Disengage claw B by pulling claw A toward you while flexing it and remove the license plate light assembly.



    E125505
  1. Turn the license plate light socket and bulb, in the directions indicated by the arrow in the illustration, to remove them.

  1. Remove the license plate light bulb from the light socket.



7. REMOVE NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE


    B134865E02
  1. Apply protective tape, as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

  1. Using an infrared light, heat the No. 2 luggage compartment door name plate.

    CAUTION:
    Do not burn yourself with the heated luggage compartment door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



    B134866E02
  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the No. 2 luggage compartment door name plate.
    Text in Illustration 
    *a
    Protective Tape

  1. Remove the protective tape.



8. REMOVE SYMBOL EMBLEM


    B134868E02
  1. Apply protective tape, as shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape

  1. Using an infrared light, heat the symbol emblem.

    CAUTION:
    Do not burn yourself with the heated luggage compartment door panel or infrared light.

    HINT:
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.



    B126357E01
  1. Using a gasket scraper with its tip wrapped in protective tape, gradually peel the adhesive surface and remove the symbol emblem.
    Text in Illustration 
    *a
    Protective Tape
    *b
    Location Pin

    HINT:
    Be careful of the location pins.

  1. Remove the protective tape.



9. REMOVE SPARE WHEEL COVER ASSEMBLY


    B136270
  1. Remove the spare wheel cover assembly.



10. REMOVE DECK FLOOR BOX RH


    B136273
  1. Remove the deck floor box RH.



11. REMOVE DECK FLOOR BOX LH

HINT:
Use the same procedure as described for the RH side.



12. REMOVE REAR FLOOR FINISH PLATE


    B349025
  1. Remove the 2 clips.

  1. Disengage the 8 claws and remove the rear floor finish plate.



13. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH


    B349026
  1. Remove the 5 clips and the luggage compartment trim cover inner RH.



14. REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH

HINT:
Use the same procedure as described for the RH side.



15. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD


    B136275
  1. Remove the luggage compartment trim inner pad.



16. REMOVE LUGGAGE COMPARTMENT DOOR WEATHERSTRIP


B140676
  1. Remove the luggage compartment door weatherstrip.