Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK (for Sedan)

FRONT DOOR LOCK (for Sedan) > INSTALLATION



1. INSTALL FRONT DOOR LOCK

NOTICE:
  1. If reusing a front door lock that has been removed, replace the door lock wire harness seal in the connecting part with a new one.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.

  1. Connect the front door lock remote control cable and the front door inside locking cable.

  1. Engage the 6 claws and close the cover.



    B116845
  1. Insert the door lock open rod into the front door lock, then set it to the door panel.

    NOTICE:
    Make sure that the outside handle link is securely engaged with the door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Using a T30 "TORX" socket wrench, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


B136172E01
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
    Text in Illustration 
    *1
    Hole Plug

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the door lock key cylinder rod is inserted.

  1. Install the hole plug.



3. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER


B348857
  1. Engage the guide and install the front door frame sub-assembly rear lower with the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }



4. INSTALL FRONT DOOR GLASS RUN


B348856
  1. Install the front door glass run.

  1. Install the clip.



5. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B351471E01
  1. Temporarily install the bolt A onto the front door window regulator sub-assembly.

  1. Insert the front door window regulator sub-assembly into the door panel. Use bolt A to hang the front door window regulator sub-assembly on the door panel.

    NOTICE:
    Do not drop the front door window regulator sub-assembly as it may be damaged.

  1. Install the front door window regulator sub-assembly with the 5 bolts and tighten the bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



6. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B351480E01
  1. Insert the front door glass sub-assembly into the door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly.



    B351469
  1. Install the front door glass sub-assembly onto the front door window regulator sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



7. INSTALL FRONT DOOR SERVICE HOLE COVER


B136187E01
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the front door service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the front door service hole cover.
    3. After attaching the front door service hole cover, check the quality of the seal.

  1. Connect the connectors and clamps.



8. INSTALL FRONT DOOR TRIM BRACKET


    B136164
  1. Install the front door trim bracket with the 2 screws.



9. INSTALL FRONT DOOR BELT MOULDING


    B134875
  1. Engage the 6 claws and install a new front door belt moulding.

  1. Remove the protective tape.



10. INSTALL OUTER REAR VIEW MIRROR
  1. Engage the claw and install the outer rear view mirror.

  1. Install the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B136161
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.



    B351468
  1. Engage the 8 clips and install the front door trim board sub-assembly.

  1. Install the clip.



    B136159
  1. Install the screw.



12. INSTALL FRONT ARMREST BASE UPPER PANEL


  1. for Driver Side:

    1. Connect the connector.



    2. B136158
    3. Engage the 7 claws and 2 clips, and install the front armrest base upper panel.

    4. Install the screw.



  1. for Front Passenger Side:

    1. Connect the 2 connectors.



    2. B141925
    3. Engage the 7 claws and 2 clips, and install the front armrest base upper panel.

    4. Install the screw.



13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B349416
  1. Engage the claw and the clip, and install the front door lower frame bracket garnish.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }