FRONT DOOR LOCK (for Sedan) > INSTALLATION |
| 1. INSTALL FRONT DOOR LOCK |
Apply MP grease to the sliding and rotating areas of the front door lock.
![]() |
Connect the front door lock remote control cable and the front door inside locking cable.
![]() |
Close the cover.
![]() |
Insert the door lock open rod into the front door lock, then set it to the door panel.
![]() |
Apply adhesive to the threads of the screws.
Using "TORX" socket wrench T30, install the front door lock with the 3 screws.
| 2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER |
![]() |
Using "TORX" socket wrench T30, install the cover with the front door lock key cylinder.
Install the hole plug.
| 3. INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER |
![]() |
Install the front door frame sub-assembly rear lower with the bolt.
| 4. INSTALL FRONT DOOR GLASS RUN |
![]() |
Install the front door glass run, then engage the clip.
| 5. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY |
Apply MP grease to the sliding and rotating areas of the front door window regulator.
w/ Power window:
![]() |
Loosely bolt A onto the front door window regulator.
Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.
Install the front door window regulator with the 5 bolts, and tighten bolt A.
Connect the connector.
![]() |
w/o Power window:
Loosely screw bolt A onto the front door window regulator.
Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.
Install the front door window regulator with the 5 bolts, and tighten bolt A.
Connect the connector.
| 6. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY |
![]() |
Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.
![]() |
Install the front door glass onto the front door window regulator with the 2 bolts.
| 7. INSTALL FRONT DOOR SERVICE HOLE COVER |
![]() |
Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.
| Area | Dimension |
| A | 2.0 mm (0.079 in.) or more |
| B | 6.0 mm (0.236 in.) or more |
| 8. INSTALL FRONT DOOR TRIM BRACKET |
![]() |
Install the front door trim bracket with the 2 screws.
| 9. INSTALL FRONT DOOR BELT MOULDING |
![]() |
Engage the 6 claws and install a new front door belt moulding.
Remove the protective tape.
| 10. INSTALL OUTER REAR VIEW MIRROR |
![]() |
Engage the claw and install the outer rear view mirror with the 3 nuts.
w/ Power mirror:
Connect the connector.
| 11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
w/ Power window:
Connect the front door lock remote control cable and front door inside locking cable.
![]() |
Engage the 9 clips and install the front door trim board.
![]() |
Install the screw.
w/o Power window:
![]() |
Connect the front door lock remote control cable and front door inside locking cable.
![]() |
Engage the 9 clips and install the front door trim board.
![]() |
Tighten the screw.
| 12. INSTALL FRONT ARMREST BASE UPPER PANEL |
![]() |
for Driver side with power window:
Connect the connector.
Engage the 7 claws and 2 clips and install the front armrest base upper panel.
Install the screw.
![]() |
for Front passenger side with power window:
Connect the connector.
Engage the 7 claws and 2 clips and install the front armrest base upper panel.
Install the screw.
![]() |
w/o Power window:
Engage the 5 clips and 2 clips and install the front armrest base upper panel.
Install the screw.
| 13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH |
![]() |
Engage the claw and clip and install the front door lower frame bracket garnish.
| 14. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window) |
![]() |
Install the window regulator handle plate.
Open all the windows.
![]() |
Install the front door window regulator handle with the clip at the angle shown in the illustration.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |