Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK (for Sedan)

REAR DOOR LOCK (for Sedan) > INSTALLATION



1. INSTALL REAR DOOR LOCK

NOTICE:
  1. If reusing a rear door lock that has been removed, replace the door lock wire harness seal in the connecting part with a new one.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the rear door lock.

  1. Connect the rear door lock remote control cable and rear door inside locking cable.

  1. Engage the 7 claws and close the 2 covers.

  1. Insert the rear door lock into the outside handle frame release plate, then set it onto the door panel.

  1. Make sure that the outside handle frame link is securely engaged with the rear door lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

  1. Using a T30 "TORX" socket wrench, install the rear door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B348867
  1. Install the rear door glass sub-assembly onto the rear door window regulator sub-assembly in the direction indicated by the arrow as shown in the illustration.



3. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B136214
  1. Install the rear door window division bar with the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }

  1. Install the screw.



4. INSTALL REAR DOOR GLASS RUN


B136213
  1. Install the rear door glass run.



5. INSTALL REAR DOOR BELT MOULDING


    B134882
  1. Engage the 5 claws and install a new rear door belt moulding.



    B134880E03
  1. Remove the protective tape.



6. INSTALL REAR DOOR WEATHERSTRIP


    B348866E01
  1. Engage the 31 clips and install the rear door weatherstrip.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Apply though pressure to the sections with double-sided tape.

  1. Install the clip.



7. INSTALL REAR DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the rear door check assembly.



    B136211E01
  1. Install the rear door check assembly onto the door panel with the 2 bolts.
    Text in Illustration 
    *a
    Door Panel
    *b
    Body Panel

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.

  1. Install the rear door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



8. INSTALL REAR DOOR SERVICE HOLE COVER


    B136230E01
  1. Apply butyl tape to the door panel and install a new rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the rear door service hole cover, pull the links and connectors out through the rear door service hole.
    2. There should be no wrinkles or folds after attaching the rear door service hole cover.
    3. After attaching the rear door service hole cover, check the quality of the seal.

  1. Connect the connectors and engage the clamps.



9. INSTALL REAR DOOR TRIM BRACKET


    B136209
  1. Install the rear door trim bracket with the 2 screws.



10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B208701
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.



    B208700
  1. Engage the 7 clips and install the rear door trim board sub-assembly.



    B208699
  1. Install the screw.



11. INSTALL REAR DOOR ARMREST BASE UPPER PANEL
  1. Connect the connector.



    B208702
  1. Engage the 7 claws and 2 clips, and install the rear door armrest base upper panel.

  1. Install the screw.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }