Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK (for Sedan)

REAR DOOR LOCK (for Sedan) > REMOVAL


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE REAR DOOR ARMREST BASE UPPER PANEL


B208702
  1. Remove the screw.

  1. Disengage the 2 clips and 7 claws.

  1. Disconnect the connector and remove the rear door armrest base upper panel.



4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B208699
  1. Remove the screw.



    B208700
  1. Disengage the 7 clips.



    B208701
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door trim board sub-assembly.



5. REMOVE REAR DOOR TRIM BRACKET


    B136209
  1. Remove the 2 screws and the rear door trim bracket.



6. REMOVE REAR DOOR SERVICE HOLE COVER


    B136210
  1. Disconnect the connectors, disengage the clamps and remove the rear door service hole cover.

    NOTICE:
    Remove any butyl tape remaining on the door side.



7. REMOVE REAR DOOR CHECK ASSEMBLY


    B136211
  1. Remove the 3 bolts and the rear door check assembly.

    NOTICE:
    Do not drop or damage the rear door check assembly when removing the bolts.

    HINT:
    Remove the rear door check assembly through the service hole.



8. REMOVE REAR DOOR WEATHERSTRIP


    B348866E01
  1. Remove the clip.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Disengage the 31 clips.

  1. Peel off the double-sided tape and remove the rear door weatherstrip.

    NOTICE:
    Remove any double-sided tape remaining on the door side.



9. REMOVE REAR DOOR BELT MOULDING


    B134880E03
  1. Apply protective tape to the door panel in the periphery of the rear door belt moulding.



    B134881E02
  1. Using a moulding remover, disengage the 5 claws and remove the rear door belt moulding.



10. REMOVE REAR DOOR GLASS RUN
  1. Connect the power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the rear door glass sub-assembly in the fully opened position.

  1. Disconnect the cable to the negative (-) battery terminal.

  1. Disconnect the power window regulator switch assembly.



    B136213
  1. Remove the rear door glass run.



11. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B136214
  1. Remove the screw.

  1. Remove the 2 bolts and the rear door window division bar sub-assembly.

    NOTICE:
    Do not drop or damage the rear door window division bar sub-assembly when removing the bolts and the screw.



12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B348868
  1. Remove the rear door glass sub-assembly in the direction indicated by the arrow as shown in the illustration.



13. REMOVE REAR DOOR LOCK


B136218
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

    NOTICE:
    Do not drop or damage the rear door lock when removing the screws.

  1. Move the rear door lock downward, remove the outside handle frame release plate and remove the rear door lock.

    HINT:
    Remove the rear door lock through the service hole.



    B349515
  1. Disengage the 7 claws and open the 2 covers.



    B127211
  1. Disconnect the rear door lock remote control cable and rear door inside locking cable.

  1. Remove the door lock wire harness seal.