Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Sedan Rear Side)

POWER WINDOW REGULATOR MOTOR (for Sedan Rear Side) > INSTALLATION



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


B132191
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "TORX" socket wrench T25, install the power window regulator motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.

    NOTICE:
    Do not apply grease to the window regulator spring.



    B136217E01
  1. Temporarily install the bolt A to the rear door window regulator sub-assembly.

  1. Insert the rear door window regulator sub-assembly into the door panel. Use bolt A to hang the rear door window regulator sub-assembly on the door panel.

    NOTICE:
    Do not drop the rear door window regulator sub-assembly as it may be damaged.

  1. Install the rear door window regulator sub-assembly with the 3 bolts, and tighten the bolt A.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B348867
  1. Install the rear door glass sub-assembly onto the rear door window regulator sub-assembly in the direction indicated by the arrow as shown in the illustration.



4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B136214
  1. Install the rear door window division bar with the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 54 in.*lbf }

  1. Install the screw.



5. INSTALL REAR DOOR GLASS RUN


B136213
  1. Install the rear door glass run.



6. INSTALL REAR DOOR BELT MOULDING


    B134882
  1. Engage the 5 claws and install a new rear door belt moulding.



    B134880E03
  1. Remove the protective tape.



7. INSTALL REAR DOOR WEATHERSTRIP


    B348866E01
  1. Engage the 31 clips and install the rear door weatherstrip.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Apply though pressure to the sections with double-sided tape.

  1. Install the clip.



8. INSTALL REAR DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the rear door check assembly.



    B136211E01
  1. Install the rear door check assembly onto the door panel with the 2 bolts.
    Text in Illustration 
    *a
    Door Panel
    *b
    Body Panel

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or the equivalent.

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.

  1. Install the rear door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



9. INSTALL REAR DOOR SERVICE HOLE COVER


    B136230E01
  1. Apply butyl tape to the door panel and install a new rear door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the rear door service hole cover, pull the links and connectors out through the rear door service hole.
    2. There should be no wrinkles or folds after attaching the rear door service hole cover.
    3. After attaching the rear door service hole cover, check the quality of the seal.

  1. Connect the connectors and engage the clamps.



10. INSTALL REAR DOOR TRIM BRACKET


    B136209
  1. Install the rear door trim bracket with the 2 screws.



11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B208701
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.



    B208700
  1. Engage the 7 clips and install the rear door trim board sub-assembly.



    B208699
  1. Install the screw.



12. INSTALL REAR DOOR ARMREST BASE UPPER PANEL
  1. Connect the connector.



    B208702
  1. Engage the 7 claws and 2 clips, and install the rear door armrest base upper panel.

  1. Install the screw.



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }