FRONT SEAT ASSEMBLY (for Sedan) > DISASSEMBLY |
| 1. REMOVE FRONT SEAT INNER BELT ASSEMBLY |
![]() |
for Driver Side:
Disconnect the seat position sensor connector.
Using a clip remover, remove the connector.
Using a clip remover, remove the clamp.
Remove the clamp.
![]() |
for Front Passenger Seat:
Using a clip remover, remove the connector.
Using a clip remover, remove the clamp.
Remove the clamp.
![]() |
Remove the wire harness from the claw of the front seat cushion inner shield.
Remove the nut and the front seat inner belt.
| 2. REMOVE FRONT SEAT CUSHION INNER SHIELD |
![]() |
Remove the screw.
| *1 | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and the clip and remove the front seat cushion outer shield.
| 3. REMOVE VERTICAL ADJUSTER COVER (w/ Vertical Adjuster) |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the vertical adjuster cover.
| *1 | Protective Tape |
| 4. REMOVE VERTICAL ADJUSTER KNOB (w/ Vertical Adjuster) |
![]() |
Remove the 2 screws and the vertical adjuster knob.
| 5. REMOVE RECLINING ADJUSTER RELEASE HANDLE |
![]() |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw and remove the reclining adjuster release handle.
| *1 | Protective Tape |
| 6. REMOVE FRONT SEAT CUSHION OUTER SHIELD |
![]() |
Remove the screw.
| *1 | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and the clip and remove the front seat cushion outer shield.
| 7. REMOVE FRONT SEAT CUSHION COVER PAD (for Cover Integrated Type) |
![]() |
Disengage the 2 claws and 7 hooks.
![]() |
Using a clip remover, remove the 2 clips and the front seat cushion cover pad.
| 8. REMOVE FRONT SEAT CUSHION PAD (for Cover Separate Type) |
![]() |
Disengage the 2 hooks.
![]() |
Remove the 2 hog rings.
![]() |
Disengage the 2 claws and the 7 hooks and remove the front seat cushion.
| 9. REMOVE FRONT SEAT CUSHION COVER (for Cover Separate Type) |
![]() |
Remove the 10 hog rings and remove the front seat cushion cover.
| 10. REMOVE FRONT SEAT HEADREST SUPPORT |
![]() |
Remove the 3 hog rings.
![]() |
Remove the 2 hog rings.
for Cover Separate Type:
![]() |
Remove the 3 hog rings
![]() |
Disengage the 2 claws and remove the front seat headrest support.
| 11. REMOVE FRONT SEATBACK COVER PAD |
![]() |
Remove the front seatback cover pad.
| 12. REMOVE FRONT SEAT BACK COVER (for Cover Separate Type) |
![]() |
Remove the 6 hog rings and the front seat back cover.
| 13. REMOVE VERTICAL ADJUSTER SPACER (w/ Vertical Adjuster) |
![]() |
Disengage the claw and remove the vertical adjuster spacer.
| 14. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover.
| 15. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Disengage the claw and remove the reclining adjuster inside cover.
| 16. REMOVE RECLINING ADJUSTER OUTSIDE COVER RH |
![]() |
Remove the screw and the reclining adjuster outside cover.
| 17. REMOVE RECLINING ADJUSTER OUTSIDE COVER LH |
| 18. REMOVE FRONT SEATBACK BRACKET |
![]() |
Remove the 2 nuts and remove the front seatback bracket sub-assembly.
| 19. REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
![]() |
w/ Vertical Adjuster:
Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
![]() |
w/o Vertical Adjuster:
Remove the screw.
Disengage the 2 claws and remove the front seat cushion lower shield.
| 20. REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
![]() |
w/ Vertical Adjuster:
Remove the screw.
Disengage the 2 claws and remove the front seat cushion lower shield.
![]() |
w/o Vertical Adjuster:
Remove the screw.
Disengage the claw and remove the front seat cushion lower shield.
| 21. REMOVE FRONT SEAT CUSHION PROTECTOR |
![]() |
Remove the 2 front seat cushion protectors.
| 22. REMOVE SEAT POSITION SENSOR PROTECTOR (for Driver Side) |
![]() |
Disengage the pin and remove the seat position sensor protector.
| 23. REMOVE SEAT POSITION SENSOR (for Driver Side) |
![]() |
Using T30 "TORX" socket wrench, remove the bolt and the seat position sensor.
| 24. REMOVE FRONT SEAT WIRE (for Front Passenger Side) |
![]() |
Disconnect the 5 connectors.
Remove the 2 clamps and the front seat wire.
| 25. REMOVE OCCUPANT DETECTION ECU (for Front Passenger Side) |
![]() |
Disengage the claw and remove the occupant detection ECU.