Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Sedan)

FRONT SEAT ASSEMBLY (for Sedan) > REASSEMBLY


CAUTION:
Wear protective gloves. Sharp surfaces on the front seat adjuster frame could cause injuries to your hands.

HINT:
The procedure described below is for the driver side of LHD. Use the same procedure for both the front passenger and driver sides of LHD, unless otherwise specified.



1. INSTALL SEAT POSITION SENSOR (for Driver Side)


    B138561E02
  1. Provisionally install the seat position sensor.
    Text in Illustration 
    *1
    Sensor
    *2
    Seat Rail
    *3
    Feeler Gauge

    NOTICE:
    1. If the seat position sensor has been damaged, or there are any cracks, dents or other defects in the case, bracket or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, make sure that the SRS wiring does not interfere with other parts and is not pinched between other parts.

  1. Install a 1 mm (0.04 in.) feeler gauge between the seat rail and seat position sensor, as shown in the illustration.

    HINT:
    Make sure that the clearance between the seat position sensor and seat rail is within 0.6 to 2 mm (0.023 to 0.079 in.).

  1. Push the top of the seat position sensor toward the seat rail.

  1. While holding the seat position sensor, tighten the bolt using T30 "TORX" socket wrench.

    Torque:
    8.0 N*m{ 80 kgf*cm , 71 in.*lbf }



2. INSTALL SEAT POSITION SENSOR PROTECTOR (for Driver Side)


  1. Engage the pin and install a new seat position sensor protector.


    B332564E01

    NOTICE:
    Do not damage portion A, shown in the illustration, when installing the seat position sensor protector.



3. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side)


    B138563
  1. Engage the claw and install the occupant detection ECU.



4. INSTALL FRONT SEAT WIRE


    B332562
  1. Install the front seat wire with the 2 clamps.

  1. Connect the 5 connectors.



5. INSTALL FRONT SEAT CUSHION PROTECTOR


    B138348
  1. Install the 2 front seat cushion protectors.



6. INSTALL FRONT SEAT CUSHION LOWER SHIELD RH


    B138344
  1. w/ Vertical Adjuster:

    1. Engage the claw and install the front seat cushion lower shield.

    2. Tighten the screw.



    B138346
  1. w/o Vertical Adjuster:

    1. Engage the 2 claws and install the front seat cushion lower shield.

    2. Tighten the screw.



7. INSTALL FRONT SEAT CUSHION LOWER SHIELD LH


    B138345
  1. w/ Vertical Adjuster:

    1. Engage the 2 claws and install the front seat cushion lower shield.

    2. Tighten the screw.



    B138347
  1. w/o Vertical Adjuster:

    1. Engage the claw and install the front seat cushion lower shield.

    2. Tighten the screw.



8. INSTALL FRONT SEATBACK BRACKET


B237805
  1. Install the front seatback bracket sub-assembly with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



9. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH


    B138343
  1. Install the reclining adjuster outside cover with the screw.



10. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH

HINT:
Use the same procedure as for the RH side.



11. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    B138341
  1. Engage the claw and install the reclining adjuster inside cover.

  1. Tighten the screw.



12. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    B332556
  1. Engage the claw and install the reclining adjuster inside cover.

  1. Tighten the screw.



13. INSTALL VERTICAL ADJUSTER SPACER (w/ Vertical Adjuster)


    B138340
  1. Engage the claw and install the vertical adjuster spacer.



14. INSTALL FRONT SEAT BACK COVER (for Cover Separate Type)


    B158534E02
  1. Using hog ring pliers, install the front seat back cover with 6 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the front seat back cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the front seatback cover with the center of the front seatback pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



15. INSTALL FRONT SEATBACK COVER PAD


    B332555
  1. Install the front seatback cover pad.



    B138335E02
  1. Using hog ring pliers, install 2 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the front seat back cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Securely tighten the hog rings as shown in the illustration.



  1. for Cover Separate Type:



      B158531E02
    1. Using hog ring pliers, install the 3 new hog rings.
      Text in Illustration 
      *1
      Hog Ring
      *2
      Hog Ring Pliers

      NOTICE:
      1. Do not soil or scratch the front seat back cover.
      2. When installing hog rings, minimize wrinkles as much as possible.
      3. Securely tighten the hog rings as shown in the illustration.



    B138337E02
  1. Using hog ring pliers, install 3 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the front seat back cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Securely tighten the hog rings as shown in the illustration.



16. INSTALL FRONT SEAT HEADREST SUPPORT


B138333E02
Text in Illustration 
*1
Protruding

HINT:
Use the same procedure for both sides.

  1. Align the protruding portion of the front seat headrest support with the installation groove of the front seat adjuster frame.

  1. Engage the 2 claws and install the front seat headrest support.



17. INSTALL FRONT SEAT CUSHION COVER (for Cover Separate Type)


    B158524E02
  1. Using hog ring pliers, install the front seat cushion cover with 10 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the front seat cushion cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Align the center of the hog ring installation area of the front seat cushion cover with the center of the front seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.



18. INSTALL FRONT SEAT CUSHION (for Cover Separate Type)


    B158522
  1. Engage the 7 hooks and the 2 claws and install the front seat cushion.



    B158521E02
  1. Using hog ring pliers, install 2 new hog rings.
    Text in Illustration 
    *1
    Hog Ring
    *2
    Hog Ring Pliers

    NOTICE:
    1. Do not soil or scratch the front seat cushion cover.
    2. When installing hog rings, minimize wrinkles as much as possible.
    3. Securely tighten the hog rings as shown in the illustration.



    B158519
  1. Engage the 2 hooks.



19. INSTALL FRONT SEAT CUSHION COVER PAD (for Adhesive Type Seat)


    B138329
  1. Install the front seat cushion cover pad with the 2 clips.



    B138330
  1. Engage the 2 claws and the 7 hooks.



20. INSTALL FRONT SEAT CUSHION OUTER SHIELD


    B138326
  1. Engage the 2 claws and the clip and install the front seat cushion outer shield.

  1. Tighten the screw.



21. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    B138324
  1. Engage the claw and install the reclining adjuster release handle.



22. INSTALL VERTICAL ADJUSTER KNOB (w/ Vertical Adjuster)


    B138322
  1. Install the vertical seat adjuster knob.

  1. Tighten the 2 screws.



23. INSTALL VERTICAL ADJUSTER COVER (w/ Vertical Adjuster)


    B138321
  1. Engage the 3 claws and install the vertical adjuster cover.



24. INSTALL FRONT SEAT CUSHION INNER SHIELD


    B138328
  1. Engage the claw and the clip and install the front seat cushion inner shield.

  1. Tighten the screw.



25. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    B138352E01
  1. Install the front seat inner belt with the nut.

    Torque:
    42 N*m{ 430 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not place the front seat inner belt over the convex areas of the front seat adjuster frame.

  1. Install the wire harness into the claw of the front seat cushion inner shield.



    B138569
  1. for Driver Side:

    1. Install the 2 clamps.

    2. Install the connector.

    3. Connect the seat position sensor connector.



    B138570
  1. for Front Passenger Side:

    1. Install the 2 clamps.

    2. Install the connector.