FRONT BUMPER (for Hatchback with Sport Package) > INSTALLATION |
| 1. INSTALL FRONT BUMPER COVER |
Install the 3 grommets.
Connect the connectors.
Engage the 10 claws and install the front bumper cover
Tighten the 3 bolts and the 5 screws.
Install the 4 clips.
| 2. PREPARE VEHICLE FOR HEADLIGHT AIMING ADJUSTMENT |
Prepare the vehicle:
| 3. PREPARE FOR HEADLIGHT AIMING (for Using a Tester) |
Prepare the vehicle for headlight aim check.
Adjust in accordance with the headlight tester instructions.
| 4. PREPARE FOR HEADLIGHT AIMING (for Using a Screen) |
![]() |
| *a | 90° |
| *b | 7.62 or 3 m (25 or 9.84 ft.) |
Prepare the vehicle in accordance with the following conditions:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (high) x 4 m (13.1 ft.) (wide)) to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen, as shown in the illustration.

| *a | Aligning distance 7.62 m (25 ft.) | *b | Aligning distance 3 m (9.84 ft.) |
| *c | V RH Line | *d | V LH Line |
| *e | V Line | *f | H Line |
| *g | 90° | *h | 7.62 m (25 ft.) |
| *i | 3 m (9.84 ft.) | - | - |
![]() |
Draw base lines (H line, V LH and V RH lines) on the screen, as shown in the illustration.
| *a | V LH Line |
| *b | V Line |
| *c | V RH Line |
| *d | H Line |
| *e | Ground |
H Line (Headlight height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low-beam headlights.
V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) headlights):
Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low-beam headlight bulbs).
| 5. INSPECT HEADLIGHT AIMING |
Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight is not being inspected from affecting the headlight aiming.
Start the engine.
Turn on the headlight and make sure that the cutoff line falls within the specified area, as shown in the illustration.

| *a | Aligning distance 7.62 m (25 ft.) | *b | Aligning distance 3 m (9.84 ft.) |
| *c | Low beam | *d | High beam |
| *e | V LH Line | *f | H Line |
| *g | Cutoff Line | *h | V RH Line |
| *i | 101 mm (3.98 in.) | *j | 39.8 mm (1.57 in.) |
| *k | 0 mm (0 in.) | - | - |
| 6. ADJUST HEADLIGHT AIMING |
![]() |
Using a screwdriver, adjust the aim.
| *1 | Aiming Screw |
| 7. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT |
Prepare the vehicle:
| 8. PREPARE FOR FOG LIGHT AIMING |
![]() |
| *a | 90° |
| *b | 7.62 or 3 m (25 or 9.84 ft.) |
Prepare the vehicle in accordance with the following conditions:
Prepare a piece of thick white paper (approximately 2 m (6.6 ft.) (high) x 4 m (13.1 ft.) (wide)), to use as a screen.
Draw a vertical line down the center of the screen (V line).
Set the screen as shown in the illustration.

| *a | Aligning distance 7.62 m (25 ft.) | *b | Aligning distance 3 m (9.84 ft.) |
| *c | V RH Line | *d | V LH Line |
| *e | V Line | *f | H Line |
| *g | 7.62 m (25 ft.) | *h | 3 m (9.84 ft.) |
| *i | 90° | - | - |
![]() |
Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.
| *a | V LH Line |
| *b | V Line |
| *c | V RH Line |
| *d | H Line |
| *e | Ground |
H Line (Fog light height):
Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.
V LH Line and V RH Line (Center mark positions of left-hand (LH) and right-hand (RH) fog lights):
Draw two vertical lines so that they intersect the H line at each center mark.
| 9. INSPECT FOG LIGHT AIMING |
Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light is not being inspected from affecting the fog light aiming.
Start the engine.
Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.

| *a | Aligning distance 7.62 m (25 ft.) | *b | Aligning distance 3 m (9.84 ft.) |
| *c | V LH Line | *d | V RH Line |
| *e | H Line | *f | 433 mm (17.06 in.) |
| *g | 52 mm (2.04 in.) | *h | Hot Zone |
| 10. ADJUST FOG LIGHT AIMING |
![]() |
Adjust the fog light aim to within the specified range by turning the aiming screw with a screwdriver.