Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER (for Hatchback with Sport Package)

FRONT BUMPER (for Hatchback with Sport Package) > REASSEMBLY



1. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY LH


    B271835
  1. Engage the 2 guides and install the front side member bracket.

  1. Tighten the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



2. INSTALL FRONT SIDE MEMBER BRACKET SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL WINDSHIELD WASHER JAR ASSEMBLY (for Cold Area Specification Vehicles)


    B288482
  1. Install the windshield washer jar with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



4. INSTALL WINDSHIELD WASHER JAR ASSEMBLY (except Cold Area Specification Vehicles)


    B288481
  1. Install the windshield washer jar with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



5. INSTALL FRONT NO. 1 BUMPER STONE DEFLECTOR BRACKET


    B288479
  1. Install the 2 nuts and front No. 1 bumper stone deflector bracket.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Use the same procedure as for the opposite side.



6. INSTALL FRONT BUMPER REINFORCEMENT


    B271833
  1. Install the 4 nuts and the front bumper reinforcement.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Tighten the 6 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



    B271832
  1. Engage the 2 clamps and install the wire harness.



7. INSTALL NO. 2 RADIATOR SIDE AIR SEAL


    B288499
  1. Engage the 2 claws and install the radiator side air seal.



8. INSTALL NO. 1 RADIATOR SIDE AIR SEAL

HINT:
Use the same procedure as for the No. 2 side.



9. INSTALL RADIATOR SUPPORT EXTENSION LH


    B288498
  1. Engage the 2 claws and install the radiator support extension.



10. INSTALL RADIATOR SUPPORT EXTENSION RH

HINT:
Use the same procedure as for the LH side.



11. INSTALL THERMISTOR ASSEMBLY


    B288497
  1. Engage the 2 clamps and install the thermistor.



12. INSTALL FRONT BUMPER SIDE RETAINER LH


    B271827
  1. Engage the 2 claws and install the front bumper side retainer.



13. INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL HEADLIGHT ASSEMBLY LH
  1. Connect the connectors.

  1. Install the headlight assembly with the 3 screws.



15. INSTALL HEADLIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



16. INSTALL FOG LIGHT COVER LH


    B273101
  1. Engage the 5 claws and install the fog light cover.



17. INSTALL FOG LIGHT COVER RH

HINT:
Use the same procedure as for the LH side.



18. INSTALL FOG LIGHT ASSEMBLY LH
  1. Engage the guide to install the fog light assembly.

  1. Install the 2 screws.

  1. Connect the connector.



19. INSTALL FOG LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



20. INSTALL RADIATOR GRILLE LOWER MOULDING


    B273410
  1. Engage the 5 claws and install the radiator grille lower moulding.

  1. Tighten the 6 screws.



21. INSTALL LOWER NO. 1 RADIATOR GRILLE


    B273100
  1. Engage the 14 claws and install the lower No. 1 radiator grille.

  1. Tighten the 2 screws.



22. INSTALL FRONT BUMPER LOWER COVER


    B273099
  1. Engage the 2 claws and install the front bumper lower cover.



23. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM


    B283029
  1. Engage the 2 guides, 4 claws and install the radiator grille (or front panel) emblem.



24. INSTALL RADIATOR GRILLE


    B273098
  1. Engage the guide, 12 claws and install the radiator grille.



    B273097
  1. Install the 3 clips.



25. INSTALL HOOD TO FRONT END PANEL SEAL
  1. Clean the attachment surface.

    1. Using an infrared light, heat the double-sided adhesive tape remaining on the front bumper cover.

      HINT:
      Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.

    2. Using a piece of cloth, rub the remaining double-sided adhesive tape off the front bumper cover while it is hot from the infrared light.

      NOTICE:
      Installing the hood to front end panel seal with any double-sided tape remaining on the front bumper cover may cause adhesion failure. Therefore, completely remove the double-sided tape.

    3. Using a non-residue solvent, clean the attachment surface.



    B288664
  1. Install a new hood to front end panel seal onto the front bumper cover, as shown in the illustration.

    NOTICE:
    Thoroughly press the hood to front end panel seal to ensure that it adheres.



    B273096
  1. Install the 4 clips.