Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for Hatchback)

FRONT DOOR (for Hatchback) > REASSEMBLY



1. INSTALL NO. 1 BLACK OUT TAPE (for 5 Door)

HINT:
Use the same procedure as for the LH side



2. INSTALL FRONT DOOR PANEL CUSHION


    B271614
  1. Install the 2 front door panel cushions.



3. INSTALL FRONT DOOR WEATHERSTRIP (for 5 Door)


    B271613
  1. Engage the 29 clips and install the front door weatherstrip.

  1. Engage the clip.



4. INSTALL FRONT DOOR WEATHERSTRIP (for 3 Door)


    B284595
  1. Engage the 32 clips and install the front door weatherstrip.

  1. Engage the clip.



5. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door check assembly.



    B271610E01
  1. Install the front door check assembly onto the door panel with the 2 bolts.
    Text in Illustration 
    *a
    Body Panel
    *b
    Door Panel

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    NOTICE:
    To prevent contamination by foreign matter, install immediately after applying adhesive.

  1. Install the front door check assembly onto the body panel with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



6. INSTALL FRONT DOOR LOCK OPEN ROD


    B268986E01
  1. Install the front door lock open rod as indicated by the arrows in the order shown in the illustration.
    Text in Illustration 
    *1
    Snap



7. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door outside handle frame sub-assembly.



    B271622
  1. Engage the 2 claws and the grommet, and install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.



    B271625
  1. Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



8. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD


    B271620
  1. Engage the 2 claws and install the front door outside handle rear pad.



9. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B271619
  1. Engage the 3 claws and install the front door outside handle front pad.



10. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B271618
  1. Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.



11. INSTALL FRONT DOOR LOCK ASSEMBLY (w/ Power Door Lock)

NOTICE:
  1. If reusing the front door lock assembly that has been removed, replace the door lock wire harness seal with a new seal.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface.
  3. Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock.

  1. Install the door lock wire harness seal to the front door lock.



    E221615E01
  1. Insert the front door lock open rod to the front door lock.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction

    HINT:
    Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



12. INSTALL FRONT DOOR LOCK ASSEMBLY (w/o Power Door Lock)

NOTICE:
  1. If reusing the front door lock assembly that has been removed, replace the door lock wire harness seal with a new seal.
  2. Make sure that no grease or dirt adheres to the door lock wire harness seal surface.
  3. Reusing the door lock wire harness seal or using a damaged door lock wire harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock.

  1. Install the door lock wire harness seal to the front door lock.



    E221615E01
  1. Insert the front door lock open rod to the front door lock.
    Text in Illustration 
    *1
    Front Door Lock Open Rod
    V100135
    Slide Direction

    HINT:
    Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a "TORX" socket wrench T30, install the front door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



13. INSTALL FRONT DOOR OUTSIDE HANDLE COVER


    B271703
  1. Engage the 2 guides and the claw, and install the front door outside handle cover to the lock cylinder.



    B271615E01
  1. Temporarily install the front door outside handle cover with lock cylinder.
    Text in Illustration 
    *1
    Hole Plug

  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.



14. INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP
  1. Install the front door fix window weatherstrip to the front door fix window glass.



15. INSTALL FRONT DOOR FIX WINDOW GLASS


    B271612
  1. Install the front door fix window glass in the direction indicated by the arrow as shown in the illustration.



16. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B271609
  1. Install the front door front lower frame sub-assembly with the 2 bolts.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }

  1. Install the screw.

    NOTICE:
    Make sure to return the rear door weatherstrip to its original condition after performing this step.

    HINT:
    Peel back the rear door weatherstrip to install the screw.



17. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B271608
  1. Engage the guide and install the front door rear lower frame sub-assembly.

  1. Install the bolt.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }



18. INSTALL FRONT DOOR GLASS RUN


    B271607
  1. Install the front door glass run.



19. INSTALL FRONT DOOR NO. 1 STIFFENER CUSHION (for 3 Door)
  1. Using a piece of cloth or similar material, rub off any double-sided tape remaining on the door panel.

  1. Using a non-residue solvent, clean the attachment surface.

  1. Remove the double-sided tape backing of the new front door No. 1 stiffener cushion.



    B284636E02
  1. Install the front door No. 1 stiffener cushion and the 2 collars with the 2 bolts.
    Text in Illustration 
    *a
    Double-sided Tape

    Torque:
    6.3 N*m{ 64 kgf*cm , 55 in.*lbf }



20. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. Install the temporary bolt to the front door window regulator sub-assembly.



    B271605E04
  1. Insert the front door window regulator sub-assembly into the door panel. Use the temporary bolt to hang the front door window regulator sub-assembly on the door panel.
    Text in Illustration 
    *a
    Temporary Bolt

  1. Tighten the 3 bolts and the temporary bolt in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the front door window regulator sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



21. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. Install the temporary bolt to the front door window regulator sub-assembly.



    B284589E04
  1. Insert the front door window regulator sub-assembly into the door panel. Use the temporary bolt to hang the front door window regulator sub-assembly on the door panel.
    Text in Illustration 
    *a
    Temporary Bolt

  1. Tighten the 2 bolts and the temporary bolt in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the front door window regulator sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



22. INSTALL FRONT DOOR GLASS NO. 1 CHANNEL FILLER (for TMC Made)
  1. Apply soapy water to a new front door glass channel filler.



    B284648E02
  1. Install the new front door glass channel No. 1 filler as shown in the illustration.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side
    *c
    87.7 mm (3.453 in.)
    *d
    84.3 mm (3.319 in.)



23. INSTALL FRONT DOOR GLASS NO. 1 CHANNEL (for TMC Made)
  1. Apply soapy water to a front door glass No. 1 channel.



    B284649E02
  1. Using a plastic-faced hammer, tap the front door glass No. 1 channel onto the front door glass sub-assembly to install the front door glass channel.
    Text in Illustration 
    *a
    Front Side
    *b
    Rear Side
    *c
    87.7 mm (3.453 in.)
    *d
    84.3 mm (3.319 in.)

    NOTICE:
    1. Be careful not to damage the front door glass sub-assembly or front door glass No. 1 channel.
    2. Make sure the position of the front door glass No. 1 channel filler does not change.



24. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. w/ Power Window:

    1. Connect the power window regulator master switch assembly

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. Disconnect the power window regulator master switch assembly.

  1. w/o Power Window:

    1. Install the front door window regulator handle assembly.

    2. Move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Remove the front door window regulator handle assembly.



    B271604E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly.



    B271602
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B271601
  1. Install the front door service hole cover.



25. INSTALL FRONT DOOR SERVICE HOLE COVER (for 5 Door)
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through a new front door service hole cover.



    B271702E01
  1. Install the new front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover, taking care to prevent wrinkles.



26. INSTALL FRONT DOOR SERVICE HOLE COVER (for 3 Door)
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through a new front door service hole cover.



    B284588E01
  1. Install the new front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover, taking care to prevent wrinkles.



27. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


    E222075E01
  1. Using an air riveter or hand riveter, install the front No. 1 speaker assembly onto the front door panel with 3 new strike rivets.

    HINT:
    Install the new strike rivets in the order shown in the illustration.

    NOTICE:

    1. B130465
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

    2. B130466
      Confirm that the rivets are seated properly against the speaker.
    3. Do not tilt the riveter when installing the rivet onto the speaker.
    4. Do not leave any space between the rivet head and speaker.

    5. B130467
      Do not leave any space between the speaker and door. Firmly hold the 2 items together while installing the rivet.

  1. Connect the connector.



28. INSTALL DOOR SIDE AIRBAG SENSOR (w/ Curtain Shield Airbag)
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Engage the guide and install the airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
    3. Make sure that the pin (stopper) is securely inserted into the body hole.
    4. Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. Connect the connector to the door side airbag sensor.

    NOTICE:
    When connecting any airbag connector, take care not to damage the airbag wire harness.




    1. Connect the connector as shown in the illustration (when locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).


      C198070E06


      Text in Illustration 
      *1
      Outer Connector Locking Sleeve
      -
      -
      *a
      Slide
      -
      -

      HINT:
      When connected, the outer connector locking sleeve will slide. Be sure not to hold the outer connector locking sleeve while connecting, as it may result in an insecure fit.

  1. Check that there is no looseness in the installation parts of the door side airbag sensor.



29. INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



30. INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING (for 3 Door)

HINT:
Use the same procedure as for the LH side .



31. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

HINT:
Use the same procedure as for the LH side .



32. INSTALL FRONT DOOR WINDOW FRAME UPPER MOULDING (for Driver Side)

HINT:
Use the same procedure as for the LH side .



33. INSTALL FRONT DOOR WINDOW FRAME FRONT MOULDING

HINT:
Use the same procedure as for the LH side .



34. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP (for 5 Door)


    B271701
  1. Engage the 7 claws and install the front door glass inner weatherstrip as shown in the illustration.



35. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP (for 3 Door)


    B284626
  1. Engage the 8 claws and install the front door glass inner weatherstrip as shown in the illustration.



36. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B271598
  1. Engage the 4 guides and install the front door inside handle sub-assembly.



37. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 5 Door)


    B271597E01
  1. Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



    B271596
  1. Engage the 7 clips and install the front door trim board sub-assembly.



    B271595
  1. Install the 3 screws.



    B275407
  1. Engage the claw and close the cover.



38. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for 3 Door)


    B271597E01
  1. Connect the front door lock remote control cable assembly and the front door inside locking cable assembly to the front door inside handle sub-assembly.
    Text in Illustration 
    *1
    Front Door Lock Remote Control Cable Assembly
    *2
    Front Door Inside Locking Cable Assembly



    B284585
  1. Engage the 8 clips and install the front door trim board sub-assembly.



    B271595
  1. Install the 3 screws.



    B275407
  1. Engage the claw and close the cover.



39. INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)
  1. Connect the connector.



    B284582
  1. Engage the 9 claws and 4 guides, and install the front armrest base upper panel.



40. INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)
  1. Connect the connector.

    HINT:
    If the armrest base upper panel is equipped with door lock switch, connect the connector.



    B284583
  1. Engage the 6 claws and 3 guides, and install the front armrest base upper panel.



41. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B271669E01
  1. Install the window regulator handle plate.
    Text in Illustration 
    *a
    Inside of Vehicle

  1. Open all the windows.



    B284599E01
  1. Install the front door window regulator handle assembly with the clip at the angle shown in the illustration.
    Text in Illustration 
    *a
    Assemble with Glass in Fully Open Position



42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



43. INSPECT POWER WINDOW OPERATION (w/ Power Window)
(Click here)


44. INSPECT SRS WARNING LIGHT (w/ Curtain Shield Airbag)
(Click here)