Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK (for Hatchback)

REAR DOOR LOCK (for Hatchback) > REMOVAL


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. REMOVE REAR DOOR FRAME GARNISH


    B271672
  1. Disengage the claw and the 2 clips.

  1. Disengage the guide and remove the rear door frame garnish.



2. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B345202E04
  1. Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and rear door trim board sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

  1. Turn the rear door window regulator handle assembly with the clip remover inserted, as shown in the illustration.

  1. Remove the rear door window regulator handle assembly and the clip.

  1. Remove the window regulator handle plate.



3. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)


    B271671
  1. Using a moulding remover, disengage the 9 claws and 3 guides.

  1. Disconnect the connector and remove the rear door armrest base upper panel.



4. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    B271670
  1. Using a moulding remover, disengage the 5 claws and 2 guides, and remove the rear door armrest base upper panel.



5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B273457E03
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *a
    Protective Tape



    B271673
  1. Remove the 3 screws.



    B271674
  1. Disengage the 7 clips.



    B271675E01
  1. Disconnect the rear door lock remote control cable assembly and the rear door inside locking cable assembly, and remove the rear door trim board sub-assembly.
    Text in Illustration 
    *1
    Rear Door Lock Remote Control Cable Assembly
    *2
    Rear Door Inside Locking Cable Assembly



6. REMOVE REAR DOOR SERVICE HOLE COVER


    B271679
  1. Remove the rear door service hole cover.

    HINT:
    Remove any butyl tape remaining on the door side.



7. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B271682
  1. Remove the 3 screws.

  1. Remove the nut and the rear door window division bar sub-assembly.



8. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
  1. w/ Power Window:

    1. Connect the power window regulator switch assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the rear door glass sub-assembly in the fully opened position.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. Disconnect the power window regulator switch assembly.

  1. w/o Power Window:

    1. Install the front door window regulator handle assembly.

    2. Move the front door glass sub-assembly so that the door glass bolt holes can be seen.

    3. Remove the front door window regulator handle assembly.



    B271683
  1. Slide the lower section of the rear door glass sub-assembly as indicated by the arrow as shown in the illustration.



    B271685E01
  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



9. REMOVE REAR DOOR GLASS RUN


    B271681
  1. Remove the clip.

  1. Disengage the 2 guides and remove the rear door glass run.



10. REMOVE REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock)


    B271689
  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, remove the 3 screws.



    E221618E01
  1. Slide the rear door lock downward, and remove the rear door lock from the release plate.
    Text in Illustration 
    *1
    Release Plate
    V100135
    Slide Direction



    E221642
  1. Remove the door lock wire harness seal from the rear door lock.



11. REMOVE REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock)


    E228977
  1. Using a T30 "TORX" wrench, remove the 3 screws.



    E221618E01
  1. Slide the rear door lock downward, and remove the rear door lock from the release plate.
    Text in Illustration 
    *1
    Release Plate
    V100135
    Slide Direction



    E221642
  1. Remove the door lock wire harness seal from the rear door lock.



12. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B271117E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws.
    Text in Illustration 
    *1
    Protective Tape



    E221643
  1. Remove the rear door lock remote control cable from rear door lock.



13. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B271119E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the 4 claws.
    Text in Illustration 
    *1
    Protective Tape



    E221644
  1. Remove the rear door inside locking cable from rear door lock.