Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR (for Hatchback)

REAR DOOR (for Hatchback) > DISASSEMBLY


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the RH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Power Window)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE REAR DOOR FRAME GARNISH


    B271672
  1. Disengage the claw and the 2 clips.

  1. Disengage the guide and remove the rear door frame garnish.



4. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    B345202E04
  1. Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and rear door trim board sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

  1. Turn the rear door window regulator handle assembly with the clip remover inserted, as shown in the illustration.

  1. Remove the rear door window regulator handle assembly and the clip.

  1. Remove the window regulator handle plate.



5. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)


    B271671
  1. Using a moulding remover, disengage the 9 claws and 3 guides.

  1. Disconnect the connector and remove the rear door armrest base upper panel.



6. REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    B271670
  1. Using a moulding remover, disengage the 5 claws and 2 guides, and remove the rear door armrest base upper panel.



7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B273457E03
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *a
    Protective Tape



    B271673
  1. Remove the 3 screws.



    B271674
  1. Disengage the 7 clips.



    B271675E01
  1. Disconnect the rear door lock remote control cable assembly and the rear door inside locking cable assembly, and remove the rear door trim board sub-assembly.
    Text in Illustration 
    *1
    Rear Door Lock Remote Control Cable Assembly
    *2
    Rear Door Inside Locking Cable Assembly



8. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B271676
  1. Disengage the 4 guides and remove the rear door inside handle sub-assembly.



9. REMOVE REAR DOOR GLASS INNER WEATHERSTRIP


    B271678
  1. Disengage the 7 claws and remove the rear door glass inner weatherstrip as shown in the illustration.



10. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)


    E222077
  1. Disconnect the connector.



    E222078
  1. Drill out the 3 rivet heads using a drill with a bit diameter of less than 4 mm (0.16 in.), and remove the rear speaker assembly from the rear door panel.

  1. Operate the drill around the rivet head circumference and cut out the flange.

    CAUTION:
    Be careful. The cut rivet is very hot.

    NOTICE:
    Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill the rivet head straight out.

  1. After drilling out the flange, continue drilling to push out the shards on the drill.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



11. REMOVE REAR DOOR SERVICE HOLE COVER


    B271679
  1. Remove the rear door service hole cover.

    HINT:
    Remove any butyl tape remaining on the door side.



12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B271682
  1. Remove the 3 screws.

  1. Remove the nut and the rear door window division bar sub-assembly.



13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
  1. w/ Power Window:

    1. Connect the power window regulator switch assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the rear door glass sub-assembly in the fully opened position.

    4. Disconnect the cable from the negative (-) battery terminal.

    5. Disconnect the power window regulator switch assembly.

  1. w/o Power Window:

    1. Install the front door window regulator handle assembly.

    2. Move the front door glass sub-assembly so that the door glass bolt holes can be seen.

    3. Remove the front door window regulator handle assembly.



    B271683
  1. Slide the lower section of the rear door glass sub-assembly as indicated by the arrow as shown in the illustration.



    B271685E01
  1. Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



14. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY (for TMC Made)


    B247064E02
  1. Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel sub-assembly.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not damage the rear door glass sub-assembly.



15. REMOVE REAR DOOR GLASS CHANNEL FILLER (for TMC Made)
  1. Remove the rear door glass channel filler.



16. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)


    B271687E03
  1. Disconnect the connector.
    Text in Illustration 
    *a
    Temporary Bolt

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the temporary bolt and the rear door window regulator sub-assembly.



17. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)


    B271688
  1. Remove the 3 bolts and the rear door window regulator.

    NOTICE:
    Do not drop or damage the rear door window regulator sub-assembly when removing the bolts.



18. REMOVE NO. 1 SEPARATOR DOOR STIFFENER CUSHION


    B284603
  1. Remove the 2 bolts, the 2 collars and the No. 1 separator door stiffener cushion.



19. REMOVE REAR DOOR GLASS RUN


    B271681
  1. Remove the clip.

  1. Disengage the 2 guides and remove the rear door glass run.



20. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:
Use the same procedure as for the LH side .



21. REMOVE REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock)


    B271689
  1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, remove the 3 screws.



    E221618E01
  1. Slide the rear door lock downward, and remove the rear door lock from the release plate.
    Text in Illustration 
    *1
    Release Plate
    V100135
    Slide Direction



    E221642
  1. Remove the door lock wire harness seal from the rear door lock.



22. REMOVE REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock)


    E228977
  1. Using a T30 "TORX" wrench, remove the 3 screws.



    E221618E01
  1. Slide the rear door lock downward, and remove the rear door lock from the release plate.
    Text in Illustration 
    *1
    Release Plate
    V100135
    Slide Direction



    E221642
  1. Remove the door lock wire harness seal from the rear door lock.



23. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    B271691
  1. Using a T30 "TORX" socket wrench, loosen the screw.



    B271706
  1. Disengage the 2 claws and remove the rear door outside handle cover.



24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B271692
  1. Remove the rear door outside handle in the direction indicated by the arrow as shown in the illustration.



25. REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD


    B271694
  1. Disengage the 3 claws and remove the rear door outside handle front pad.



26. REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD


    B271695
  1. Disengage the 2 claws and remove the rear door outside handle rear pad.



27. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B271696
  1. Using a T30 "TORX" socket wrench, loosen the screw.



    B271698
  1. Disengage the grommet and the 2 claws, and remove the rear door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.



28. REMOVE REAR DOOR CHECK ASSEMBLY


    B271690
  1. Remove the 3 bolts and the rear door check assembly.



29. REMOVE REAR DOOR WEATHERSTRIP


    B271699
  1. Using a clip remover, disengage the 2 clips.

  1. Using a clip remover, disengage the 29 clips and remove the rear door weatherstrip.



30. REMOVE NO. 2 BLACK OUT TAPE

HINT:
Use the same procedure as for the LH side .