Home › Drivetrain ยท DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for TMMF Made Hatchback)

FRONT DRIVE SHAFT ASSEMBLY (for TMMF Made Hatchback) > REASSEMBLY

for Preparation Click here



1. INSTALL FRONT DRIVE SHAFT DUST COVER


    C286844E01
  1. Using SST, steel plate and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.
    Text in Illustration 
    *a
    Steel Plate

    SST
    09527-10011  

    NOTICE:
    1. Install the front drive shaft dust cover in the correct orientation.
    2. Do not deform the front drive shaft dust cover.



2. INSTALL FRONT AXLE OUTBOARD JOINT BOOT


C127681E18
  1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Wrap the spline of the outboard joint shaft assembly with protective tape.
    Text in Illustration 
    *a
    Protective Tape

  1. Install new parts onto the outboard joint shaft assembly in the following order.

    1. Front No. 2 axle outboard joint boot clamp
    2. Front axle outboard joint boot
    3. Front axle outboard joint boot clamp

  1. Pack the joint portion of the outboard joint shaft assembly and the front axle outboard joint boot with grease.

    Standard grease capacity:
    151 to 161 g (5.4 to 5.6 oz.)

  1. Install the front axle outboard joint boot into the outboard joint shaft assembly groove.

    NOTICE:
    Keep the groove free of grease.



3. INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
  1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.



    C112671E01
  1. Place SST onto the front No. 2 axle outboard joint boot clamp.

    SST
    09521-24010  

  1. Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    C112672E04
  1. Using SST, adjust the clearance of the front No. 2 axle outboard joint boot clamp.

    SST
    09240-00020  

    Standard clearance:
    0.8 mm (0.0315 in.) or less

    NOTICE:
    If the measured value exceeds the specified value, retighten the front No. 2 axle outboard joint boot clamp.



4. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP
  1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Install the front axle outboard joint boot clamp to the front axle outboard joint boot.



    C112669E01
  1. Place SST onto the front axle outboard joint boot clamp.

    SST
    09521-24010  

  1. Tighten SST so that the front axle outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    C112670E01
  1. Using SST, adjust the clearance of the front axle outboard joint boot clamp.

    SST
    09240-00020  

    Standard clearance:
    0.8 mm (0.0315 in.) or less

    NOTICE:
    If the measured value exceeds the specified value, retighten the front axle outboard joint boot clamp.



5. INSTALL FRONT DRIVE SHAFT DAMPER RH (for RH Side)


C231529E04
  1. Install the front drive shaft damper RH onto the outboard joint shaft assembly dimension (A) shown in the illustration.

    Dimension (A):
    462.6 to 466.6 mm (1.52 to 1.53 ft.)

    NOTICE:
    Install the front drive shaft damper RH in the correct orientation.



6. INSTALL FRONT DRIVE SHAFT DAMPER CLAMP RH (for RH Side)
  1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Install a new front drive shaft damper clamp RH to the front drive shaft damper RH.

    NOTICE:
    Be sure to install the front drive shaft damper clamp RH on the front drive inboard joint assembly side in the correct position.



    C201462E01
  1. Place SST onto the front drive shaft damper clamp RH.

    SST
    09521-24010  

  1. Tighten SST so that the front drive shaft damper clamp RH is pinched.

    NOTICE:
    Do not overtighten SST.



    C231530E01
  1. Using SST, adjust the clearance of the front drive shaft damper clamp RH.

    SST
    09240-00020  

    Standard clearance:
    0.8 mm (0.0315 in.) or less

    NOTICE:
    If the measured value exceeds the specified value, retighten the front drive shaft damper clamp RH.



7. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Install new parts onto the outboard joint shaft assembly in the following order.

    1. Front axle inboard joint boot clamp
    2. Front axle inboard joint boot
    3. Front No. 2 axle inboard joint boot clamp

  1. Fix the outboard joint shaft assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Remove the protective tape.



    F047445E07
  1. Align the matchmarks and install the tripod joint assembly to the outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Face the serrated side of the tripod joint assembly outward and install it onto the outboard joint shaft assembly end.

  1. Using a brass bar and hammer, install the tripod joint assembly.

    NOTICE:
    1. Do not hit the rollers.
    2. Keep the tripod joint free of foreign matter.



    C160822
  1. Using a snap ring expander, install a new snap ring to the outboard joint shaft assembly.

  1. Pack the front drive inboard joint assembly with grease.

    Standard grease capacity:
    100 to 113.5 g (3.5 to 4.0 oz.)



    C160821E11
  1. Align the matchmarks and install the front drive inboard joint assembly to the outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Install the front axle inboard joint boot into the grooves of the front drive inboard joint assembly and the outboard joint shaft assembly.

    NOTICE:
    Keep the grooves free of grease.



8. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
  1. Hold the outboard joint shaft assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Install the front axle inboard joint boot clamp to the front axle inboard joint boot.



    C241890E01
  1. Place SST onto the front axle inboard joint boot clamp.

    SST
    09521-24010  

  1. Tighten SST so that the front axle inboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.



    C241891E01
  1. Using SST, adjust the clearance of the front axle inboard joint boot clamp.

    SST
    09240-00020  

    Standard clearance:
    0.8 mm (0.0315 in.) or less

    NOTICE:
    If the measured value exceeds the specified value, retighten the front axle inboard joint boot clamp.



9. INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
  1. Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.



    C205466E01
  1. Adjust dimension (A) until the drive shaft is within the specified length.

    Dimension (A):
    LH
    RH
    561.8 mm (1.84 ft.)
    803.8 mm (2.64 ft.)



    C286842
  1. Using needle-nose pliers, engage the 2 claws and install the front No. 2 axle inboard joint boot clamp as shown in the illustration.

    NOTICE:
    1. Do not damage the front axle inboard joint boot.
    2. Do not deform the claw of the hook.



10. INSPECT FRONT DRIVE SHAFT ASSEMBLY


    C205473
  1. Check for noticeable looseness when turning the joint up and down, left and right, and in the thrust direction.

  1. Check for cracks, damage and grease leakage on the boot joint.

    HINT:
    Keep the drive shaft level while moving it.



    C205466E01
  1. Check dimension (A).

    Dimension (A):
    LH
    RH
    561.8 mm (1.84 ft.)
    803.8 mm (2.64 ft.)