Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (for Hatchback)

ENGINE IMMOBILISER SYSTEM (for Hatchback) > TERMINALS OF ECU



CHECK TRANSPONDER KEY AMPLIFIER

B167608E15

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    D140-7 (AGND) - Body ground
    -
    GR - Body ground
    Ground
    Always
    Below 1 Ω
    -
    D140-1 (VC5) - D140-7 (AGND)
    Input
    P - GR
    Transponder key amplifier power supply
    No key in ignition key cylinder
    Below 1 V
    -
    D140-4 (CODE) - D140-7 (AGND)
    Output
    G - GR
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    -
    D140-5 (TXCT) - D140-7 (AGND)
    Input
    L - GR
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    -

  2. Check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    D140-1 (VC5) - D140-7 (AGND)
    Input
    P - GR
    Transponder key amplifier power supply
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 1)
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    (If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above)
    D140-4 (CODE) - D140-7 (AGND)
    Output
    G - GR
    Demodulated signal of key code data
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 2)
    D140-5 (TXCT) - D140-7 (AGND)
    Input
    L - GR
    Key code output signal
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 3)



  3. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B287844E04
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D140-1 (VC5) - D140-7 (AGND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    2. B287845E04
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D140-4 (CODE) - D140-7 (AGND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    4. B287846E06
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D140-5 (TXCT) - D140-7 (AGND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY

B271269E04

  1. Disconnect the D139 transponder key ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    D139-16 (GND) - Body ground
    -
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    -
    D139-1 (+B) - D139-16 (GND)
    Input
    Y - BR
    Battery
    Always
    11 to 14 V
    +B
    D139-2 (IG) - D139-16 (GND)
    Input
    V - BR
    Ignition switch
    Ignition switch off
    Below 1 V
    IG SW
    Ignition switch ON
    11 to 14 V
    D139-3 (KSW) - D139-16 (GND)
    Input
    BE - BR
    Unlock warning switch
    No key in ignition key cylinder
    10 kΩ or higher
    Key SW/B2780
    Key inserted in ignition key cylinder
    Below 1 Ω

  3. Reconnect the D139 transponder key ECU connector.

  4. Measure the resistance and voltage, and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    D139-14 (VC5) - D139-16 (GND)
    Input
    P - BR
    Transponder key amplifier power supply
    No key in ignition key cylinder
    Below 1 V
    1. BCC Malfunction
    2. Abnormal Status
    3. Different Encrypt Code
    4. Different Serial Number
    (If immobiliser key code certification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above)
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 1)
    D139-4 (TXCT) - D139-16 (GND)
    Input
    L - BR
    Key code output signal
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 2)
    D139-15 (CODE) - D139-16 (GND)
    Output
    G - BR
    Demodulated signal of key code data
    No key in ignition key cylinder
    Below 1 V
    Key inserted in ignition key cylinder
    Pulse generation (See waveform 3)
    D139-13 (EFIO) - D139-16 (GND)
    Input
    R - BR
    ECM output signal
    Ignition switch off
    Below 1 V
    E/G Start Permission
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
    Pulse generation (See waveform 4)
    D139-12 (EFII) - D139-16 (GND)
    Output
    LG - BR
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
    Pulse generation (See waveform 5)
    E/G Start Permission
    D139-8 (IND) - D139-16 (GND)
    Output
    SB - BR
    Theft warning indicator light signal
    Engine immobiliser system set
    Pulse generation
    Immobiliser
    Engine immobiliser system unset
    Below 1 V
    D139-9 (D) - D139-16 (GND)
    Input/Output
    B - BR
    Diagnosis tester communication
    Always
    Pulse generation
    -
    D139-5 (AGND) - Body ground
    -
    GR - Body ground
    Transponder key amplifier ground
    Always
    Below 1 Ω
    -



  5. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B287844E05
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D139-14 (VC5) - D139-16 (GND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    2. B287846E07
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D139-4 (TXCT) - D139-16 (GND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    4. B287845E05
    5. Waveform 3 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D139-15 (CODE) - D139-16 (GND)
      Tool Setting
      1 V/DIV., 20 ms./DIV.
      Condition
      Key inserted in ignition key cylinder



    6. Waveform 4 (Reference)


      B288668E15


      Text in Illustration 
      *a
      Waveform A
      *b
      Waveform B
      *c
      Approximately 160 ms
      *d
      Approximately 510 ms
      *e
      Approximately 270 ms
      -
      -
      Measurement Condition 
      Item
      Content
      Tester Connection
      D139-13 (EFIO) - D139-16 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected



    7. Waveform 5 (Reference)


      B288667E17


      Text in Illustration 
      *a
      Waveform A
      *b
      Waveform B
      *c
      Approximately 160 ms
      *d
      Approximately 510 ms
      *e
      Approximately 270 ms
      -
      -
      Measurement Condition 
      Item
      Content
      Tester Connection
      D139-12 (EFII) - D139-16 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected


CHECK ECM

A247842E26

  1. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    C51-16 (E1) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    A72-1 (BATT) - C51-16 (E1)
    Input
    Y - W-B
    +B power supply
    Always
    11 to 14 V
    -
    A72-3 (+B2) - C51-16 (E1)
    Input
    L - W-B
    +B power supply
    Ignition switch ON
    11 to 14 V
    -
    A72-2 (+B) - C51-16 (E1)
    Input
    B - W-B
    +B power supply
    Ignition switch ON
    11 to 14 V
    -
    A72-29 (IMO) - C51-16 (E1)
    Input
    W - W-B
    Transponder key ECU assembly communication input
    Ignition switch off
    11 to 14 V
    -
    Transponder key ECU assembly communication input
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
    Pulse generation
    (See waveform 1)
    -
    A72-28 (IMI) - C51-16 (E1)
    Output
    G - W-B
    Transponder key ECU assembly communication output
    Ignition switch off
    11 to 14 V
    -
    Transponder key ECU assembly communication output
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected
    Pulse generation
    (See waveform 2)
    -



  2. Inspect using an oscilloscope.



    1. Waveform 1 (Reference)


      B288667E18


      Text in Illustration 
      *a
      Waveform A
      *b
      Waveform B
      *c
      Approximately 160 ms
      *d
      Approximately 510 ms
      *e
      Approximately 270 ms
      -
      -
      Measurement Condition 
      Item
      Content
      Tester Connection
      A72-29 (IMO) - C51-16 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected



    2. Waveform 2 (Reference)


      B288668E16


      Text in Illustration 
      *a
      Waveform A
      *b
      Waveform B
      *c
      Approximately 160 ms
      *d
      Approximately 510 ms
      *e
      Approximately 270 ms
      -
      -
      Measurement Condition 
      Item
      Content
      Tester Connection
      A72-28 (IMI) - C51-16 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and reconnected