AIR CONDITIONING PANEL (for Hatchback) > INSPECTION |
| 1. INSPECT NO. 1 HEATER CONTROL SUB-ASSEMBLY |
Check the resistance of the fresh/recirc switch.
![]() |
Measure the resistance according to the value(s) in the table below.
| *1 | Fresh/Recirc Switch |
| *2 | Recirc Indicator |
| *a | Component without harness connected (No. 1 Heater Control Sub-assembly) |
| Tester Connection | Switch Condition | Specified Condition |
| 3 (FRS) - 4 (REC) | Fresh/Recirc switch ON | 10 kΩ or higher |
| Fresh/Recirc switch OFF | Below 1 Ω | |
| 5 (LED+) - 4 (REC) | Fresh/Recirc switch ON | Below 1 Ω |
| Fresh/Recirc switch OFF | 10 kΩ or higher |
Check the recirc indicator operation.
Connect the positive (+) lead from the battery to terminal 2 (A/C+) and the negative (-) lead to terminal 4 (REC).
Push the fresh/recirc switch in and check that the indicator lights up.
Check the illumination operation.
Connect the positive (+) lead from the battery to terminal 7 (ILL+) and the negative (-) lead to terminal 6 (ILL-), then check that the bulb illuminates.
| 2. INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY |
Check the heater control resistance.
![]() |
Measure the resistance according to the value(s) in the table below.
| *1 | Rear Defogger Switch |
| *2 | Rear Defogger Indicator |
| *a | Component with harness connected (No. 2 Heater Control Sub-assembly) |
| Tester Connection | Switch Condition | Specified Condition |
| ALL - 5 (E) | OFF | 10 kΩ or higher |
| 4 (LO) - 5 (E) | LO | Below 1 Ω |
| 4 (LO) - 5 (E) - 9 (M1) | LO - M1 | Below 1 Ω |
| 4 (LO) - 5 (E) - 9 (M1) | M1 | Below 1 Ω |
| 4 (LO) - 5 (E) - 9 (M1) - 10 (M2) | M1 - M2 | Below 1 Ω |
| 4 (LO) - 5 (E) - 10 (M2) | M2 | Below 1 Ω |
| 4 (LO) - 5 (E) - 10 (M2) - 6 (HI) | M2 - HI | Below 1 Ω |
| 4 (LO) - 5 (E) - 6 (HI) | HI | Below 1 Ω |
w/ Rear Window defogger:
Check the rear defogger indicator operation.
Connect the positive (+) lead from the battery to terminal 3 (IG+) and the negative (-) lead to terminal 5 (E).
Push the rear defogger switch in and check that the indicator lights up.
Check the illumination operation.
Connect the positive (+) lead from the battery to terminal 7 (ILL+) and the negative (-) lead to terminal 1 (ILL-), then check that the bulb illuminates.
| 3. INSPECT NO. 3 HEATER CONTROL SUB-ASSEMBLY |
Check the No. 3 heater control resistance.
![]() |
Measure the resistance according to the value(s) in the table below.
| *1 | A/C Switch |
| *2 | A/C Indicator |
| *a | Component without harness connected (No. 3 Heater Control Sub-assembly) |
| Tester Connection | Switch Condition | Specified Condition |
| 2 (B) - 3 (A/C) | A/C switch OFF | 10 kΩ or higher |
| 2 (B) - 3 (A/C) | A/C switch ON | Below 1 Ω |
w/ Max Hot Switch:
Check the No. 3 heater control resistance.
Check the A/C indicator operation.
Connect the positive (+) lead from the battery to terminal 2 (B) and the negative (-) lead to terminal 4 (AIND).
Push the air conditioning switch in and check that the indicator lights up.
Check the illumination operation.
Connect the positive (+) lead from the battery to terminal 5 (ILL+) and the negative (-) lead to terminal 6 (ILL-), then check that the bulb illuminates.