STARTER (for Hatchback for Cold Area Specification Vehicles) > INSPECTION |
| 1. INSPECT STARTER ASSEMBLY |
Perform a pull-in test.
Disconnect the field coil lead wire from terminal C.
![]() |
Connect the battery to the magnet starter switch as shown in the illustration and check that the pinion gear moves outward.
| *1 | Terminal 50 |
| *2 | Terminal C |
| *3 | Body |
Perform a holding test.
![]() |
Check that the pinion gear does not return inward after the cable is disconnected from terminal C.
| *1 | Terminal 50 |
| *2 | Terminal C |
| *3 | Body |
![]() |
Inspect the clutch pinion gear return.
| *1 | Terminal 50 |
| *2 | Terminal C |
| *3 | Body |
Disconnect the negative (-) lead from the switch body.
Check that the pinion gear moves inward.
If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.
Perform an operation test without load.
Connect the lead wire to terminal C.
Clamp the starter in a vise.
![]() |
Connect the battery and ammeter to the starter as shown in the illustration.
| *1 | Terminal 50 |
| *2 | Terminal 30 |
| *3 | Body |
Check that the starter rotates smoothly and steadily with the clutch pinion gear extended.
Check that the ammeter indicates the specified current.
| Tester Connection | Condition | Specified Condition |
| Battery positive terminal - Terminal 30 - Terminal 50 | 11.5 V | Below 90 A |
| 2. INSPECT MAGNET STARTER SWITCH ASSEMBLY |
![]() |
Check the plunger.
Push in the plunger, then check that it returns quickly to its original position.
If necessary, replace the magnet starter switch assembly.
![]() |
Check the pull-in coil for an open circuit.
Measure the resistance according to the value(s) in the table below.
| *1 | Terminal 50 |
| *2 | Terminal C |
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Terminal C | Always | Below 1 Ω |
![]() |
Check the holding coil for an open circuit.
Measure the resistance according to the value(s) in the table below.
| *1 | Terminal 50 |
| *2 | Switch Body |
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Body ground | Always | Below 2 Ω |
| 3. INSPECT STARTER ARMATURE ASSEMBLY |
![]() |
Check the commutator.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Segment - Segment | Always | Below 1 Ω |
![]() |
Check the commutator.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Commutator - Armature | Always | 10 kΩ or higher |
Check the commutator surface for dirt and burns. If the surface is dirty or burnt, restore it with sandpaper (No. 400) or a lathe.
![]() |
Check the commutator circuit for runout.
Place the commutator on V-blocks.
Using a dial indicator, measure the circle runout.
![]() |
Using a vernier caliper, measure the commutator diameter.
![]() |
Check that the undercut portion is clean and free of foreign matter. Smooth out the edges.
| 4. INSPECT STARTER BRUSH HOLDER ASSEMBLY |
Remove the claw of the spring, then remove the 4 brushes.
Using a vernier caliper, measure the brush length.

| *1 | Brush | *2 | Spring |
| *3 | Length | - | - |
![]() |
Check the brush holder.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A - B | Always | 10 kΩ or higher |
| A - C | Always | 10 kΩ or higher |
| A - D | Always | Below 1 Ω |
| B - C | Always | Below 1 Ω |
| B - D | Always | 10 kΩ or higher |
| C - D | Always | 10 kΩ or higher |
| 5. INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY |
Check the gear teeth of the planetary gear and starter center bearing clutch for wear or damage.
If any planetary gear is damaged, replace the planetary gear assembly.
If any gear of the starter center bearing clutch is damaged, replace the starter center bearing clutch sub-assembly.
![]() |
Check the movement of the clutch pinion gear.
| *a | Free |
| *b | Lock |
Hold the starter clutch, rotate the clutch pinion gear clockwise, and check that it turns freely.
Try to rotate the clutch pinion gear counterclockwise and check that it locks.
If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.